This paper provides a prototype neural prosthesis system dedicated to restoring continence and micturition function for patients with lower urinary tract diseases, such as detrusor hyperreflexia and detrusor-sphincter dyssynergia. This system consists of an ultra low-noise electroneurogram (ENG) signal recording module, a bi-phasic electrical stimulator module and a control unit for closed-loop bladder monitoring and controlling. In order to record extremely weak ENG signal from extradural sacral nerve roots, the system provides a programmable gain from 80 dB to 117 dB. By combining of advantages of commercial-off-the-shelf (COTS) electronics and custom designed IC, the recording front-end acquires a fairly low input-referred noise (IRN) of 0.69 μVrms under 300 Hz to 3 kHz and high area-efficiency. An on-chip multi-steps single slope analog-to-digital converter (ADC) is used to digitize the ENG signals at sampling rate of 10 kSPS and achieves an effective number of bits (ENOB) of 12.5. A bi-phasic current stimulus generator with wide voltage supply range (±0.9 V to ±12.5 V) and variable output current amplitude (0-500 μA) is introduced to overcome patient-depended impedance between electrode and tissue electrolyte. The total power consumption of the entire system is 5.61 mW. Recording and stimulation function of this system is switched by control unit with time division multiplexing strategy. The functionality of this proposed prototype system has been successfully verified through in-vivo experiments from dogs extradural sacral nerve roots.

The unique characteristic of Ternary ripple-carry addition enables us to optimize Ternary Full Adder for this specific application. Carbon nanotube field effect transistors are used in this paper to design new Ternary Half and Full Adders, which are essential components of Ternary ripple-carry adder. The novel designs take the sum of input variables as a single input signal, and generate outputs in a way which is far more efficient than the previously presented similar structures. The new ripple-carry adder operates rapidly, with high performance, and low-transistor-count.

A ladder lottery, known as the “Amidakuji” in Japan, is a network with n vertical lines and many horizontal lines each of which connects two consecutive vertical lines. Each ladder lottery corresponds to a permutation. Ladder lotteries are frequently used as natural models in many areas. Given a permutation π, an algorithm to enumerate all ladder lotteries of π with the minimum number of horizontal lines is known. In this paper, given a permutation π and an integer k, we design an algorithm to enumerate all ladder lotteries of π with exactly k horizontal lines.

A high-speed and low-power 8-bit subranging analog-to-digital converter (ADC) based on 65-nm CMOS technology was fabricated. Rather than using digital foreground calibration, an analog-centric approach was adopted to reduce power dissipation. An offset cancelling charge-steering amplifier and capacitive-averaging technique effectively reduce the offset, noise, and power dissipation of the ADC. Moreover, the circuit used to compensate the kickback noise current from the comparator can also reduce the power dissipation. The reference-voltage generator for the fine ADC is composed of a fine ladder and a capacitor providing an AC signal path. This configuration reduces the power dissipation of the selection signal drivers for the analog multiplexer. A test chip fabricated using 65-nm digital CMOS technology achieved a high sampling rate of 1GHz, a low power dissipation of 17.5mW, and a figure of merit of 118fJ/conv.-step.

This study presents efficient algorithms for performing multiply-by-3 (3N) and divide-by-3 (N/3) operations with the additions and subtractions, respectively. No multiplications and divisions are needed. Full adder (FA) and full subtractor (FS) can be implemented to realize the N3 and N/3 operations, respectively. For fast hardware implementation, this paper introduces two basic cells UCA and UCS for 3N and N/3 operations, respectively. For 3N operation, the UCA-based ripple carry adder (RCA) and carry lookahead adder (CLA) designs are proposed and their speed performances are estimated based on the delay data of standard cell library in TSMC 0.18µm CMOS process. Results show that the 16-bit UCA-based RCA is about 3 times faster than the conventional FA-based RCA and even 25% faster than the FA-based CLA. The proposed 16-bit and 64-bit UCA-based CLAs are 62% and 36% faster than the conventional FA-based CLAs, respectively. For N/3 operations, ripple borrow subtractor (RBS) is also presented. The 16-bit UCS-based RBS is about 15.5% faster than the 16-bit FS-based RBS.

A recursive construction of (k+1)-ary error-correcting signature code is proposed to identify users for MAAC, even in the presence of channel noise. The recursion is originally from a trivial signature code. In the (j-1)-th recursion, from a signature code with minimum distance of 2j-2, a longer and larger signature code with minimum distance of 2j-1 is obtained. The decoding procedure of signature code is given, which consists of error correction and user identification.

We propose a low-overhead fault-secure parallel prefix adder. We duplicate carry bits for checking purposes. Only one half of normal carry bits are compared with the corresponding redundant carry bits, and the hardware overhead of the adder is low. For concurrent error detection, we also predict the parity of the result. The adder uses parity-based error detection and it has high compatibility with systems that have parity-based error detection. We can implement various fault-secure parallel prefix adders such as Sklansky adder, Brent-Kung adder, Han-Carlson adder, and Kogge-Stone adder. The area overhead of the proposed adder is about 15% lower than that of a previously proposed adder that compares all the carry bits.

We propose an asynchronous datapath for the low-density parity-check decoder to decrease power consumption. Glitches and redundant computations are decreased by the asynchronous design. Taking advantage of the statistical characteristics of the input data, we develop novel key arithmetic elements in the datapath to reduce redundant computations. Two other types of datapaths, including normal synchronous design and clock-gating design, are implemented for comparisons with the proposed design. The three designs use similar architectures and realize the same function by using the 0.18µm process of the Semiconductor Manufacturing International Corporation. Post-layout result shows that the proposed asynchronous design exhibits the lowest power consumption. The proposed asynchronous design saves 48.7% and 21.9% more power than the normal synchronous and clock-gating designs, respectively. The performance of the proposed datapath is slightly worse than the clock-gating design but is better than the synchronous design. The proposed design is approximately 7% larger than the other two designs.

This paper presents symmetric and full swing designs of multiplier and full adder cells, based on weighted inputs for nanotechnology. Carbon Nanotube Field Effect Transistors (CNTFETs) are used to implement the circuits. Proposed designs are simulated using the HSPICE simulation tool and they are compared with their counterparts in terms of delay, power consumption and power-delay product. Significant improvements have been achieved at different voltage levels and different frequencies, load capacitors and temperatures have also been tested. Finally, process variation issue has been analyzed and the results have been reported.

In this paper, a fifth order curer low-pass filter using as switched-capacitor (SC) architecture is proposed and fabricated with TSMC 0.18 µm CMOS process. A fully differential SC is adopted via the bilinear transform of the corresponding analogue RLC passive prototype. To reach the largest possible input dynamic range and save chip area, the method of dynamic range scaling and minimum capacitor scaling is used. Measured results show that the proposed filter achieves a pass-band of 12.1 MHz with a sampling rate of 100 MHz, a SFDR of 50 dB, a stop-band attenuation greater than 50 dB and a power consumption of 48.5 mW at 1.8 V power supply. Including pads, the chip area occupies 1.515 (1.391.09) mm2. This paper has the feature of low noise, excellent linearity of the filter, and high stability. The experimental results show that it has perfect performance for WiMAX applications and standard is recommended.

To measure the detrusor pressure for diagnosing lower urinary tract symptoms, we designed a small-area and low-power System on a Chip (SoC). The SoC should be small and low power because it is encapsulated in tiny air-tight capsules which are simultaneously inserted in the urinary bladder and rectum for several days. Since the SoC is also required to be programmable, we designed an Application Specific Instruction set Processor (ASIP) for pressure measurement and wireless communication, and implemented almost required functions on the ASIP. The SoC was fabricated using a 0.18 µm CMOS mixed-signal process and the chip size is 2.5 2.5 mm2. Evaluation results show that the power consumption of the SoC is 93.5 µW, and that it can operate the capsule for seven days with a tiny battery.

We propose a C-testable multiple-block carry select adder with respect to the cell fault model. Full adders and 2:1 multiplexers are considered as cells. By an additional external input, we obtain a C-testable carry select adder. We only modify the least significant position of each block. The adder is testable with a test set consisting of 16 patterns regardless of the size of each block and the number of blocks. This is the minimum test set for the adder. We show two gate-level implementations of the adder which are testable with a test set of 9 patterns and 7 patterns respectively, with respect to the single stuck-at fault model.

The reduction in the gate length of the current devices to 65 nm causes their I-V characteristics to depart from the traditional MOSFETs. As a result, manufacturing of new efficient devices in nanoscale is inevitable. The fundamental properties of the metallic and semi-conducting carbon Nanotubes (CNTs) make them alternatives to the conventional silicon-based devices. In this paper an ultra high-speed and energy-efficient full adder is proposed, using Carbon Nanotube Field Effect Transistor (CNFET) in nanoscale. Extensive simulation results using HSPICE are reported to show that the proposed adder consumes lower power, and is faster compared to the previous adders.

Multi-operand adders, which calculates the summation of more than two operands, usually consist of compressor trees which reduce the number of operands to two without any carry propagation, and a carry-propagate adder for the two operands in ASIC implementation. The former part is usually realized using full adders or (3;2) counters like Wallace-trees in ASIC, while adder trees or dedicated hardware are used in FPGA. In this paper, an approach to realize compression trees on FPGAs is proposed. In case of FPGA with m-input LUT, any counters with up to m inputs can be realized with one LUT per an output. Our approach utilizes generalized parallel counters (GPCs) with up to m inputs and synthesizes high-performance compressor trees by setting some intermediate height limits in the compression process like Dadda's multipliers. Experimental results show that the number of GPCs are reduced by up to 22% compared to the existing heuristic. Its effectivity on reduction of delay is also shown against existing approaches on Altera's Stratix III.

This paper proposes ladder-logic programming model for sensor actuator networks. We also demonstrate optimized operations of them with central controller-based device management (CCDM) architecture. A wireless sensor actuator network consists of distributed wireless nodes, and implementing data streams and data processors onto these wireless nodes has been challenging. System programmers have to describe their instructions by a programming language, and data processors must be placed so that it optimizes, for example, total network traffic. The ladder-logic model enables the programming of them, and CCDM makes various types of optimizations feasible, including the optimization of network traffic, delivery latency, load-balancing and fault-tolerance even though these algorithms are not lightweight. In this paper, we focus on traffic reduction case, and propose two moderately complex algorithms. The experiment has shown that CCDM achieves optimizations even with such moderately complex algorithms.

We have designed and implemented a 4-bit Carry Look-ahead Adder (CLA) and 4-bit parallel multipliers to be used for the Fast Fourier Transform (FFT) system with the estimated clock frequency of 20 GHz. Through some high frequency functional tests, we have confirmed that the operation of the CLA has been successful. Through some low speed tests, we have also confirmed that the operation of multiplication has been successful. In addition, we have designed a 4-bit multiplier with a Booth encoder and with a 2-point-4-bit butterfly circuit.

A C-testable 4-2 adder tree for an easily testable high-speed multiplier is proposed, and a recursive method for test generation is shown. By using the specific patterns that we call 'alternately inverted patterns,' the adder tree, as well as partial product generators, can be tested with 14 patterns regardless of its operand size under the cell fault model. The test patterns are easily fed through the partial product generators. The hardware overhead of the 4-2 adder tree with partial product generators for a 64-bit multiplier is about 15%. By using a previously proposed easily testable adder as the final adder, we can obtain an easily testable high-speed multiplier.

In this paper an ultra high speed CNFET Full-Adder cell is presented. This design generates sum and carry-out signals via majority and majority-not gates which are implemented by CNFET buffer, CNFET inverter and input capacitors. Significant improvement in terms of speed and Power-Delay Product (PDP) is achieved.

A single flux quantum (SFQ) logic cell library has been developed for the 10 kA/cm2 Nb multi-layer fabrication process to efficiently design large-scale SFQ digital circuits. In the new cell library, the critical current density of Josephson junctions is increased from 2.5 kA/cm2 to 10 kA/cm2 compared to our conventional cell library, and the McCumber-Stwart parameter of each Josephson junction is increased to 2 in order to increase the circuit operation speed. More than 300 cells have been designed, including fundamental logic cells and wiring cells for passive interconnects. We have measured all cells and confirmed they stably operate with wide operating margins. On-chip high-speed test of the toggle flip-flop (TFF) cell has been performed by measuring the input and output voltages. The TFF cell at the input frequency of up to 400 GHz was confirmed to operate correctly. Also, several fundamental digital circuits, a 4-bit concurrent-flow shift register and a bit-serial adder have been designed using the new cell library, and the correct operations of the circuits have been demonstrated at high clock frequencies of more than 100 GHz.

Recent advances of superconducting single-flux-quantum (SFQ) circuit technology make it attractive to investigate computing systems using SFQ circuits, where arithmetic circuits play important roles. In order to develop excellent SFQ arithmetic circuits, we have to design or select their underlying algorithms, called hardware algorithms, from different point of view than CMOS circuits, because SFQ circuits work by pulse logic while CMOS circuits work by level logic. In this paper, we compare implementations of hardware algorithms for addition by synchronous-clocking SFQ circuits. We show that a set of individual bit-serial adders and Kogge-Stone adder are superior to others.