The implementation security of the RSA cryptosystem, under the threat of side-channel analysis, has attracted the attentions of many researchers. Boer et al. had proposed the MRED-DPA attack on RSA-CRT by choosing ciphertexts of equi-distant data. Their attack can be applied to RSA-OAEP decryption but not RSA-PSS signing because of the PSS random padding. We propose a new DPA attack on an implementation of RSA-CRT, with the Montgomery reduction. The proposed attack assumes only known ciphertexts, and can be applied to both RSA-OAEP decryption and RSA-PSS signing even if a random padding technique is used in practice. This study also presents experimental results to verify the proposed attack. Finally, this study proposes a CRT-based message blinding technique as a low-cost DPA countermeasure.

Lattice-reduction (LR) technique has been adopted to improve the performance and reduce the complexity in MIMO data detection. This paper presents an improved quantization scheme for LR aided MIMO detection based on Gram-Schmidt orthogonalization. For the LR aided detection, the quantization step applies the simple rounding operation, which often leads to the quantization errors. Meanwhile, these errors may result in the detection errors. Hence the purpose of the proposed detection is to further solve the problem of degrading the performance due to the quantization errors in the signal estimation. In this paper, the proposed quantization scheme decreases the quantization errors using a simple tree search with a threshold function. Through the analysis and the simulation results, we observe that the proposed detection can achieve the nearly optimal performance with very low complexity, and require a little additional complexity compared to the conventional LR-MMSE detection in the high Eb/N0 region. Furthermore, this quantization error reduction scheme is also efficient even for the high modulation order.

Energy-harvesting devices are materials that allow ambient energy sources to be converters into usable electrical power. While a battery powers the modern embedded systems, these energy-harvesting devices power the energy-harvesting embedded systems. This claims a new energy efficient management techniques for the energy-harvesting systems dislike the previous management techniques. The higher entire system efficiency in an energy-harvesting system can be obtained by a higher generating efficiency, a higher consuming efficiency, or a higher transferring efficiency. This paper presents a generalized technique for a dynamic reconfiguration and a task scheduling considering the power loss in DC-DC converters in the system. The proposed technique minimizes the power loss in the DC-DC converter and charger of the system. The proposed technique minimizes the power loss in the DC-DC converters and charger of the system. Experiments with actual application demonstrate that our approach reduces the total energy consumption by 22% in average over the conventional approach.

Test power has become a critical issue, especially for low-power devices with deeply optimized functional power profiles. Particularly, excessive capture power in at-speed scan testing may cause timing failures that result in test-induced yield loss. This has made capture-safety checking mandatory for test vectors. However, previous capture-safety checking metrics suffer from inadequate accuracy since they ignore the time relations among different transitions caused by a test vector in a circuit. This paper presents a novel metric called the Transition-Time-Relation-based (TTR) metric which takes transition time relations into consideration in capture-safety checking. Detailed analysis done on an industrial circuit has demonstrated the advantages of the TTR metric. Capture-safety checking with the TTR metric greatly improves the accuracy of test vector sign-off and low-capture-power test generation.

With the technology scaling down, leakage power becomes an important part of total power consumption. The relatively large leakage current weakens the energy recovery capability of adiabatic circuits and reduces its superiority, compared with static CMOS circuits in the field of low-power design. In this paper, we rebuild three types of adiabatic circuits (2N2N2P, IPAL and DCPAL) based on FinFET devices to obtain a large leakage power reduction by rationally utilizing the different operating modes of FinFET devices (SG, LP, and IG). A 16-bit adiabatic adder has been investigated to demonstrate the advantages of FinFET adiabatic circuits. The Predictive Technology Model (PTM) is used for 32-nm bulk MOSFET and FinFET devices and all of the simulations are based on HSPICE. The results evince the proposed FinFET adiabatic circuits have a considerable reduction (more than 60% for SG mode FinFET and more than 80% for LP mode FinFET) of power consumption compared with the bulk MOSFET ones. Furthermore, the FinFET adiabatic circuits also have higher limiting frequency of clock source and better noise immunity.

Feature selection is a technique to screen out less important features. Many existing supervised feature selection algorithms use redundancy and relevancy as the main criteria to select features. However, feature interaction, potentially a key characteristic in real-world problems, has not received much attention. As an attempt to take feature interaction into account, we propose 1-LSMI, an 1-regularization based algorithm that maximizes a squared-loss variant of mutual information between selected features and outputs. Numerical results show that 1-LSMI performs well in handling redundancy, detecting non-linear dependency, and considering feature interaction.

The 10-gigabit Ethernet passive optical network (10G-EPON) is a promising candidate for the next generation of fiber-to-the-home access systems. In the symmetric 10G-EPON system, the gigabit Ethernet passive optical network (GE-PON) and 10G-EPON will have to co-exist on the same optical network. For this purpose, an optical triplexer (10G-transmitter, 1G-transmitter, and 10G/1G-receiver) for optical line terminal (OLT) transceivers in 10G/1G co-existing EPON systems has been developed. Reducing the size and cost of the optical triplexer has been one of the largest issues in the effort to deploy 10G-EPON systems for practical use. In this paper, we describe a novel small and low-cost dual-rate optical triplexer for use in 10G-EPON applications. By reducing the optical path length by means of a light collection system with a low-magnification long-focus coupling lens, we have successfully miniaturized the optical triplexer for use in 10G-EPON OLT 10-gigabit small form factor pluggable (XFP) transceivers and decreased the number of lenses. A low-cost design of sub-assemblies also contributes to cost reduction. The triplexer's performance complies with IEEE 802.3av specifications.

Multi-view video consists of multiple video sequences which are captured by multiple closely spaced cameras from different angles and positions. It enables each user to freely switch viewpoints by playing different video sequences. However, the transmission of multi-view video requires more bandwidth than conventional multimedia. To reduce the bandwidth, UDMVT (User Dependent Multi-view Video Transmission) based on MVC (Multi-view Video Coding) for a single user has been proposed. In UDMVT, the same frames are encoded into different versions for different users, which increases the redundant transmission. To overcome this problem and extend UDMVT to multiple users' environment, this paper proposes UMSM (User dependent Multi-view video Streaming for Multi-users). UMSM calculates the overlapping and un-overlapping frame area for multiple users from all frames based on feedback information at a server. Proposed UMSM exploits the combination of multicasting overlapping area to multiple users and unicasting un-overlapping area to each user. By means of this concept, UMSM only transmits required frames for each user. To achieve further reduction of the traffic, UMSM combines other two features with this concept. The first one is that offset of the requests from multiple users is aligned periodically to maximize the overlapping frame area. The second one is that the SP-frames standardized in H.264/AVC are exploited as the anchor frame of overlapping frame area to prevent redundant transmissions of overlapping frames. The combination of these three techniques achieves substantial reduction of the transmission bitrate for multiple users in multi-view video streaming. Simulation results using benchmark test sequences provided by MERL show that UMSM decreases the transmission bit-rate 47.2% on average for 4 users are watching the same multi-view video compared to UDMVT.

In DHT network, a node can get/put a requested data by only log N look-up steps. However, conventional DHT network only supports single query look-up to search data. From the reason, each node in a DHT network must execute look-up process for each query even if a large number of put and get operations are executed. Therefore, this results in high network load in massive data management such as MapReduce, sensor network, and web information. To address the problem, we propose multiple queries look-up architecture using range information feedback (MARIF). MARIF extends the conventional KBR protocol to supports range information that is a scope of ID space a node keeps. When a source node receives range information from a destination node, the source node checks all queries in the range information and forwards queries matching the range information to the destination node directly. This effectively reduces the number of look-up queries and the network load for the IP network. In addition, MARIF can be implemented into conventional DHT networks and can easily be combined to effective DHT routing algorithms such as Chord, Kademlia, Pastry, and one-hop DHT. In evaluation, we implement MARIF into three DHT networks and compare its performance with that of conventional query bundling mechanisms based on the KBR protocol. The results show that MARIF reduces by up to 40% the total number of forwarding queries to put data compared with other mechanisms. In addition, MARIF saves the number of forwarding queries per look-up process by up to 85% compared to other mechanisms with low bundling overhead.

In Long-Term Evolution (LTE)-Advanced, heterogeneous networks are important to further improve the system throughput per unit area. In heterogeneous network deployment, low power nodes such as picocells are overlaid onto macrocells. In the downlink, the combined usage of inter-cell interference coordination (ICIC), which is a technique that reduces the severe interference from macrocells by reducing the transmission power or stopping the transmission from the macrocells, and cell range expansion (CRE), which is a technique that expands the cell radius of picocells by biasing the received signal power, is very effective in improving the system and cell-edge user throughput. In this paper, we consider two types of ICIC. The first one reduces the transmission power from the macrocells (referred to as reduced power ICIC) and the second one stops the transmission from the macrocells (referred to as zero power ICIC). This paper investigates the impact of the reduction in the transmission power when using reduced power ICIC and the restriction on the modulation scheme caused by the reduction in the transmission power when using reduced power ICIC on the user throughput performance with the CRE offset value as a parameter. In addition, the throughput performance when applying reduced power ICIC is compared to that when applying zero power ICIC. Simulation results show that the user throughput with reduced power ICIC is not sensitive to the protected subframe ratio compared to that with zero power ICIC even if the modulation scheme is restricted to only QPSK in the protected subframes. This indicates that reduced power ICIC is more robust than zero power ICIC for non-optimum protected subframe ratios.

In this paper, 1) it is shown that amplitude-only images (AOIs) have quite wide intensity ranges (IRs), and 2) an IR reduction method for AOIs is proposed. An AOI is the inversely transformed amplitude spectra of an image, and it is used in the privacy- and copyright-protected image trading system because of its invisibility. Since an AOI is the coherent summation of cosine waves with the same phase, the IR of the AOI is too large to be stored and/or transmitted. In the proposed method, random signs are applied to discrete Fourier transformed amplitude coefficients to obtained AOIs with significantly lower IRs without distortion while keeping the invisibility of images. With reasonable processing time, high correct watermark extracting rates, inversely quantized AOIs with low mean squared errors, and reconstructed images with high peak signal-to-noise ratios are obtained by a linear quantizer in the proposed method.

This paper discusses the reduction of the amount of transmitted information for the efficient use of frequency resources in wireless feedback control systems, and clarify the effect of the reduction of the amount of transmitted information. As a typical example of the underactuated controlled object, a rotary inverted pendulum is considered. We propose a reduction method for state information fed back from the controller to the controlled object. It estimates angle or velocity state from the previous state. In addition, we propose a reduction method that temporally omits less important control information and state information. Numerical examples clarify the effect of the reduction methods on the control quality. And we show that the reduction methods achieve large reduction of the amount of transmitted information with small disadvantage of the control quality.

This paper proposes a novel multichannel speech enhancement technique for reverberant rooms that is effective when noise sources are spatially stationary, such as a projector fan noise, an air-conditioner noise, and unwanted speech sources at the back of microphones. Speech enhancement performance of the conventional multichannel Wiener filter (MWF) degrades when the Signal-to-Noise Ratio (SNR) of the current microphone input signal changes from the noise-only period. Furthermore, the MWF structure is computationally inefficient, because the MWF updates the whole spatial beamformer periodically to track switching of the speakers (e.g. turn-taking). In contrast to the MWF, the proposed method reduces noise independently of the SNR. The proposed method has a novel two-stage structure, which reduces noise and distortion of the desired source signal in a cascade manner by using two different beamformers. The first beamformer focuses on noise reduction without any constraint on the desired source, which is insensitive to SNR variation. However, the output signal after the first beamformer is distorted. The second beamformer focuses on distortion reduction of the desired source signal. Theoretically, complete elimination of distortion is assured. Additionally, the proposed method has a computationally efficient structure optimized for spatially stationary noise reduction problems. The first beamformer is updated only when the speech enhancement system is initialized. Only the second beamformer is updated periodically to track switching of the active speaker. The experimental results indicate that the proposed method can reduce spatially stationary noise source signals effectively with less distortion of the desired source signal even in a reverberant conference room.

This paper presents a decoupling capacitance boosting method for the resonant supply noise reduction by fast voltage hopping of DVS systems. The proposed method utilizes a foot transistor as a switch between a conventional decoupling capacitor (decap) and GND. The switching controls of the foot transistor depending on the supply noise states achieve an effective noise reduction as well as fast settling time compared with the conventional passive decaps. The measurement results of a test chip fabricated in a 0.18 µm CMOS technology show 12X boost of effective decap value, and 65.8% supply noise reduction with 96% settling time improvement.

In this paper, we investigate a relationship between the length-decreasing self-reducibility and the many-one-like reducibilities for partial multivalued functions. We show that if any parsimonious (many-one or metric many-one) complete function for NPMV (or NPMVg) is length-decreasing self-reducible, then any function in NPMV (or NPMVg) has a polynomial-time computable refinement. This result implies that there exists an NPMV (or NPMVg)-complete function which is not length-decreasing self-reducible unless P = NP.

Multihigh-dimensional chaotic systems were reduced to low-dimensional space embedded equations (SEEs), and their macroscopic and statistical properties were investigated using eigen analysis of the moment vector equation (MVE) of the SEE. First, the state space of the target system was discretized into a finite discrete space. Next, an embedding from the discrete space to a low-dimensional discrete space was defined. The SEE of the target system was derived using the embedding. Finally, eigen analysis was applied to the MVE of the SEE to derive the properties of the target system. The geometric increase in the dimension of the MVE with the dimension of the target system was avoided by using the SEE. The pdfs of arbitrary elements in the target nonlinear system were derived without a reduction in accuracy due to dimension reduction. Moreover, since the dynamics of the system were expressed by the eigenvalues of the MVE, it was possible to identify multiple steady states that cannot be done using numerical simulation. This approach can thus be used to analyze the macroscopic and statistical properties of multi-dimensional chaotic systems.

This paper proposes an inner-product encryption (IPE) scheme, which achieves selectively fully-attribute-hiding security in the standard model almost tightly reduced from the decisional linear (DLIN) assumption, and whose ciphertext is almost the shortest among the existing (weakly/fully) attribute-hiding IPE schemes, i.e., it consists of n+4 elements of G and 1 element of GT for a prime-order symmetric bilinear group (G, GT), where n is the dimension of attribute/predicate vectors. We also present a variant of the proposed IPE scheme that enjoys shorter public and secret keys with preserving the security. A hierarchical IPE (HIPE) scheme can be realized that has short ciphertexts and selectively fully-attribute-hiding security almost tightly reduced from the DLIN assumption.

This paper proposes a lattice-reduction-aided MIMO-OFDM receiver with virtual channels; the receiver enables an increase in the downlink transmission speed for a user where the number of transmit antennas is considerably higher than that of the receive antennas. However, the receiver has a higher computational complexity than conventional lattice-reduction-aided MIMO receivers. Accordingly, we also propose novel techniques to reduce the computational complexity for the lattice-reduction-aided MIMO receivers with virtual channels. The proposed MIMO receiver achieves superior performance in 102 MIMO-OFDM systems. Furthermore, the proposed techniques are shown to reduce the computational complexity to approximately 40% of the original configuration in the 102 MIMO-OFDM systems.

Given an integer n-dimensional lattice basis, the random sampling reduction was proven to find a short vector in arithmetic steps with an integer k, which is freely chosen by users. This paper introduces new random sampling reduction using precomputation techniques. The computation cost is almost independent of the lattice dimension number. The new method is therefore especially advantageous to find a short lattice vector in higher dimensions. The arithmetic operation number of our new method is about 20% of the random sampling reduction with 200 dimensions, and with 1000 dimensions it is less than 1% ( 1/130) of that of the random sampling reduction with representative parameter settings under reasonable assumptions.

Network devices, such as routers or L3 switches, have a feature called packet-filtering for network security. They determine whether or not to pass arriving packets by applying filtering rules to them. If the number of comparisons of packets with rules increases, the time required for a determination will increase, which will result in greater communication delay. Various algorithms for optimizing filtering tables to minimize the load of packet filtering, which directly impacts the communication delay, have been proposed. In this paper, first we introduce an adaptive packet filter based on an algorithm that reconstructs the filtering table according to the frequency distribution of arrival packets. Next, we propose a new reconstruction algorithm based on grouping of dependent rules. Grouping dependent rules makes it possible to sort the rules in the table by the frequency of matching. Finally, we show the effectiveness of our algorithm by comparing it against previously reported algorithms.