In this paper, a reference-voltage self-selected pseudo-differential sensing scheme suitable for single-ended SRAM is proposed. The proposed sensing scheme can select different reference voltage according to the offset direction. With the employment of the new sensing scheme, the swing of the read bit-line in the read operation is reduced by 74.6% and 45.5% compared to the conventional domino and the pseudo-differential sense amplifier sensing scheme, respectively. Therefore, the delay and power consumption of the read operation are significantly improved. Simulation results based on a standard 55nm CMOS show that compared with the conventional domino and pseudo-differential sensing schemes, the sensing delay is improved by 66.4% and 47.7%, and the power consumption is improved by 31.4% and 22.5%, respectively. Although the area of the sensing scheme is increased by 50.8% compared with the pseudo-differential sense amplifier sensing scheme, it has little effect on the entire SRAM area.

We propose a sampling method that incorporates a normally distributed sampling series for EEG measurements using compressed sensing. We confirmed that the ADC sampling count and amount of wirelessly transmitted data can be reduced by 11% while maintaining a reconstruction accuracy similar to that of the conventional method.

This paper presents a fully integrated yet compact receiver front-end for Sub-GHz applications such as Internet-of-Things (IoT). The low noise amplifier (LNA) matching network leverages an inductance boosting technique. A relatively small on-chip inductor with a compact area achieves impedance matching in such a low frequency. Moreover, a passive-mixer-first mode bypasses the LNA to extend the receiver dynamic-range. The passive mixer provides matching to the 50Ω antenna interface to eliminate the need for additional passive components. Therefore, the receiver can be fully-integrated without any off-chip matching components. The flipped-voltage-follower (FVF) cell is adopted in the low pass filter (LPF) and the variable gain amplifier (VGA) for its high linearity and low power consumption. Fabricated in 65nm LP CMOS process, the proposed receiver front-end occupies 0.37mm2 core area, with a tolerable input power ranging from -91.5dBm to -1dBm for 500kbps GMSK signal at 924MHz frequency. The power consumption is 1mW power under a 1.2V supply.

The adiabatic quantum-flux-parametron (AQFP) is an energy-efficient superconductor logic element based on the quantum flux parametron. AQFP circuits can operate with energy dissipation near the thermodynamic and quantum limits by maximizing the energy efficiency of adiabatic switching. We have established the design methodology for AQFP logic and developed various energy-efficient systems using AQFP logic, such as a low-power microprocessor, reversible computer, single-photon image sensor, and stochastic electronics. We have thus demonstrated the feasibility of the wide application of AQFP logic in future information and communications technology. In this paper, we present a tutorial review on AQFP logic to provide insights into AQFP circuit technology as an introduction to this research field. We describe the historical background, operating principle, design methodology, and recent progress of AQFP logic.

Elliptic curve cryptography (ECC), one of the asymmetric cryptography, is widely used in practical security applications, especially in the Internet of Things (IoT) applications. This paper presents a low-power reconfigurable architecture for ECC, which is capable of resisting simple power analysis attacks (SPA) and can be configured to support all of point operations and modular operations on 160/192/224/256-bit field orders over GF(p). Point multiplication (PM) is the most complex and time-consuming operation of ECC, while modular multiplication (MM) and modular division (MD) have high computational complexity among modular operations. For decreasing power dissipation and increasing reconfigurable capability, a Reconfigurable Modular Multiplication Algorithm and Reconfigurable Modular Division Algorithm are proposed, and MM and MD are implemented by two adder units. Combining with the optimization of operation scheduling of PM, on 55 nm CMOS ASIC platform, the proposed architecture takes 0.96, 1.37, 1.87, 2.44 ms and consumes 8.29, 11.86, 16.20, 21.13 uJ to perform one PM on 160-bit, 192-bit, 224-bit, 256-bit field orders. It occupies 56.03 k gate area and has a power of 8.66 mW. The implementation results demonstrate that the proposed architecture outperforms the other contemporary designs reported in the literature in terms of area and configurability.

In this paper, we describe a post-processing technique having high extraction efficiency (ExE) for de-biasing and de-correlating a random bitstream generated by true random number generators (TRNGs). This research is based on the N-bit von Neumann (VN_N) post-processing method. It improves the ExE of the original von Neumann method close to the Shannon entropy bound by a large N value. However, as the N value increases, the mapping table complexity increases exponentially (2N), which makes VN_N unsuitable for low-power TRNGs. To overcome this problem, at the algorithm level, we propose a waiting strategy to achieve high ExE with a small N value. At the architectural level, a Hamming weight mapping-based hierarchical structure is used to reconstruct the large mapping table using smaller tables. The hierarchical structure also decreases the correlation factor in the raw bitstream. To develop a technique with high ExE and low cost, we designed and fabricated an 8-bit von Neumann with waiting strategy (VN_8W) in a 130-nm CMOS. The maximum ExE of VN_8W is 62.21%, which is 2.49 times larger than the ExE of the original von Neumann. NIST SP 800-22 randomness test results proved the de-biasing and de-correlation abilities of VN_8W. As compared with the state-of-the-art optimized 7-element iterated von Neumann, VN_8W achieved more than 20% energy reduction with higher ExE. At 0.45V and 1MHz, VN_8W achieved the minimum energy of 0.18pJ/bit, which was suitable for sub-pJ low energy TRNGs.

This paper presents a miniaturized transformer-based ultra-low-power (ULP) LC-VCO with embedded supply pushing reduction techniques for IoT applications in 65-nm CMOS process. To reduce the on-chip area, a compact transformer patterned ground shield (PGS) is implemented. The transistors with switchable capacitor banks and associated components are placed underneath the transformer, which further shrinking the on-chip area. To lower the power consumption of VCO, a gm-stacked LC-VCO using the transformer embedded with PGS is proposed. The transformer is designed to provide large inductance to obtain a robust start-up within limited power consumption. Avoiding implementing an off/on-chip Low-dropout regulator (LDO) which requires additional voltage headroom, a low-power supply pushing reduction feedback loop is integrated to mitigate the current variation and thus the oscillation amplitude and frequency can be stabilized. The proposed ULP TF-based LC-VCO achieves phase noise of -114.8dBc/Hz at 1MHz frequency offset and 16kHz flicker corner with a 103µW power consumption at 2.6GHz oscillation frequency, which corresponds to a -193dBc/Hz VCO figure-of-merit (FoM) and only occupies 0.12mm2 on-chip area. The supply pushing is reduced to 2MHz/V resulting in a -50dBc spur, while 5MHz sinusoidal ripples with 50mVPP are added on the DC supply.

Approximate multiplier design is an effective technique to improve hardware performance at the cost of accuracy loss. The current approximate multipliers are mostly ASIC-based and are dedicated for one particular application. In contrast, FPGA has been an attractive choice for many applications because of its high performance, reconfigurability, and fast development round. This paper presents a novel methodology for designing approximate multipliers by employing the FPGA-based fabrics (primarily look-up tables and carry chains). The area and latency are significantly reduced by applying approximation on carry results and cutting the carry propagation path in the multiplier. Moreover, we explore higher-order multipliers on architectural space by using our proposed small-size approximate multipliers as elementary modules. For different accuracy-hardware requirements, eight configurations for approximate 8×8 multiplier are discussed. In terms of mean relative error distance (MRED), the error of the proposed 8×8 multiplier is as low as 1.06%. Compared with the exact multiplier, our proposed design can reduce area by 43.66% and power by 24.24%. The critical path latency reduction is up to 29.50%. The proposed multiplier design has a better accuracy-hardware tradeoff than other designs with comparable accuracy. Moreover, image sharpening processing is used to assess the efficiency of approximate multipliers on application.

Addition is a key fundamental function for many error-tolerant applications. Approximate addition is considered to be an efficient technique for trading off energy against performance and accuracy. This paper proposes a carry-maskable adder whose accuracy can be configured at runtime. The proposed scheme can dynamically select the length of the carry propagation to satisfy the quality requirements flexibly. Compared with a conventional ripple carry adder and a conventional carry look-ahead adder, the proposed 16-bit adder reduced the power consumption by 54.1% and 57.5%, respectively, and the critical path delay by 72.5% and 54.2%, respectively. In addition, results from an image processing application indicate that the quality of processed images can be controlled by the proposed adder. Good scalability of the proposed adder is demonstrated from the evaluation results using a 32-bit length.

This work presents the lowest power consumption sub-mm2 supply-modulated OOK transmitter for self-powering a continuous glucose monitoring (CGM) contact lens. By combining the transmitter with a glucose fuel cell that functions as both the power source and a sensing transducer, a self-powered CGM contact lens was developed. The 385×385μm2 test chip implemented in 65-nm standard CMOS technology operates at 270pW with a supply voltage of 0.165V. Self-powered operation of the transmitter using a 2×2mm2 solid-state glucose fuel cell was thus demonstrated.

This paper surveys advances in biomedical processor SoC technology for healthcare application and reviews state-of-the-art architecture and circuits used in SoC integration. Particularly, this paper categorizes and describes techniques for improving power efficiency in communication, computation, and sensing. Additionally, it surveys accuracy enhancement techniques for bio-signal measurement and recognition. Finally, we have discussed the potential new directions for development as well as research.

This study proposes a design and calibration method for a small-footprint, low-frequency, and low-power gate leakage timer using a differential leakage technique for IoT applications. The proposed gate leakage timer is different from conventional ones because it is composed of two leakage sources and exploits differential leakage current for the charging capacitor. This solution alleviates the inherent trade-off between small-footprint and low-frequency in the conventional gate leakage timer. Furthermore, a calibration method to suppress variations of the output frequency is proposed in this paper. To verify the effectiveness of the proposed gate leakage timer, a test chip was fabricated using 55-nm-DDC-CMOS technology. The test chip successfully demonstrates the highest figure of merit (FoM) of the product of the capacitor area (0.072µm2) and output frequency (0.11Hz), which corresponds to an improvement by a factor of 2,121 compared to the conventional one. It also demonstrates the operation with 4.5pW power consumption. The total footprint can be reduced to be 28µm2, which enables low-cost and low-power IoT edges. The scaling scenario shows that the proposed technique is conducive to technology scaling.

Approximate computing is a promising paradigm to realize fast, small, and low power characteristics, which are essential for modern applications, such as Internet of Things (IoT) devices. This paper proposes the Carry-Predicting Adder (CPredA), an approximate adder that is scalable relative to accuracy and power consumption. The proposed CPredA improves the accuracy of a previously studied adder by performing carry prediction. Detailed simulations reveal that, compared to the existing approximate adder, accuracy is improved by approximately 50% with comparable energy efficiency. Two application-level evaluations demonstrate that the proposed approximate adder is sufficiently accurate for practical use.

Multiplication is a key fundamental function for many error-tolerant applications. Approximate multiplication is considered to be an efficient technique for trading off energy against performance and accuracy. This paper proposes an accuracy-controllable multiplier whose final product is generated by a carry-maskable adder. The proposed scheme can dynamically select the length of the carry propagation to satisfy the accuracy requirements flexibly. The partial product tree of the multiplier is approximated by the proposed tree compressor. An 8×8 multiplier design is implemented by employing the carry-maskable adder and the compressor. Compared with a conventional Wallace tree multiplier, the proposed multiplier reduced power consumption by between 47.3% and 56.2% and critical path delay by between 29.9% and 60.5%, depending on the required accuracy. Its silicon area was also 44.6% smaller. In addition, results from two image processing applications demonstrate that the quality of the processed images can be controlled by the proposed multiplier design.

In this paper, we propose an IEEE 802.15.10-based layer 2 routing (L2R) method with a load balancing algorithm; the proposal considers fairness in terms of the cumulative number of sending packets at each terminal to resolve the packet concentration problem for the IEEE 802.15.4-based low-power consumption wireless smart utility network (Wi-SUN) systems. The proposal uses the accumulated sending times of each terminal as a weight in calculating each path quality metric (PQM) to decide multi-hopping routes with load balancing in the network. Computer simulation of the mesh network with 256 terminals shows that the proposed routing method can improve the maximum sending ratio (MSR), defined as the ratio of the maximum sending times to the average number of sending times in the network, by 56% with no degradation of the end-to-end communication success ratio (E2E-SR). The proposed algorithm is also experimentally evaluated by using actual Wi-SUN modules. The proposed routing method also improves the MSR by 84% with 70 terminals. Computer simulations and experiments prove the effectiveness of the proposed method in terms of load balancing.

To deal with the reliability issue caused by soft errors, this paper proposed a low power soft error hardened latch (SHC) design using a novel Schmitt-Trigger-based C-element for reliable low power applications. Unlike state-of-the-art soft error tolerant latches that are usually based on hardware redundancy with large area overhead and high power consumption, the proposed SHC latch is implemented through double-sampling and node-checking using a novel Schmitt-Trigger-based C-element, which can help to reduce the area overhead and the corresponding power consumption as well. The evaluation results show that the total number of transistors of the proposed SHC latch is only increased by 2 when compared to the conventional unhardened C2MOS latch, while up to 20.35% and 82.96% power reduction can be achieved when compared to the conventional unhardened C2MOS latch and the existing soft error tolerant HiPeR design, respectively.

CMOS microprocessors are limited in their capacity for clock speed improvement because of increasing computing power, i.e., they face a power-wall problem. Single-flux-quantum (SFQ) circuits offer a solution with their ultra-fast-speed and ultra-low-power natures. This paper introduces our contributions towards ultra-high-speed cryogenic SFQ computing. The first step is to design SFQ microprocessors. From qualitatively and quantitatively evaluating past-designed SFQ microprocessors, we have found that revisiting the architecture of SFQ microprocessors and on-chip caches is the first critical challenge. On the basis of cross-layer discussions and analysis, we came to the conclusion that a bit-parallel gate-level pipeline architecture is the best solution for SFQ designs. This paper summarizes our current research results targeting SFQ microprocessors and on-chip cache architectures.

We propose a radiation-hardened Flip-Flop (FF) with stacked transistors based on the Adaptive Coupling Flip-Flop (ACFF) with low power consumption in a 65 nm FDSOI process. The slave latch in ACFF is much weaker against soft errors than the master latch. We design several FFs with stacked transistors in the master or slave latches to mitigate soft errors. We investigate radiation hardness of the proposed FFs by α particle and neutron irradiation tests. The proposed FFs have higher radiation hardness than a conventional DFF and ACFF. Neutron irradiation and α particle tests revealed no error in the proposed AC Slave-Stacked FF (AC_SS FF) which has stacked transistors only in the slave latch. We also investigate radiation hardness of the proposed FFs by heavy ion irradiation. The proposed FFs maintain higher radiation hardness up to 40 MeV-cm2/mg than the conventional DFF. Stacked inverters become more sensitive to soft errors by increasing tilt angles. AC_SS FF achieves higher radiation hardness than ACFF with the performance equivalent to that of ACFF.

This work presents a low-complexity lossless electrocardiogram (ECG) compression ASIC for wireless sensors. Three linear predictors aiming for different signal characteristics are provided for prediction based on a history table that records of the optimum predictors for recent samples. And unlike traditional methods using a unified encoder, the prediction error is encoded by a hybrid Golomb encoder combining Exp-Golomb and Golomb-Rice and can adaptively configure the encoding scheme according to the predictor selection. The novel adaptive prediction and encoding scheme contributes to a compression rate of 2.77 for the MIT-BIH Arrhythmia database. Implemented in 40nm CMOS process, the design takes a small gate count of 1.82K with 37.6nW power consumption under 0.9V supply voltage.

In order to realize an Internet-of-Things (IoT) with tiny sensors integrated in our buildings, our clothing, and the public spaces, battery lifetime and battery size remain major challenges. Power reduction in IoT sensor nodes is determined by both sleep mode as well as active mode contributions. A power state machine, at the system level, is the key to achieve ultra-low average power consumption by alternating the system between active and sleep modes efficiently. While, power consumption in the active mode remains dominant, other power contributions like for timekeeping in standby and sleep conditions are becoming important as well. For example, non-conventional critical blocks, such as crystal oscillator (XO) and resistor-capacitor oscillator (RCO) become more crucial during the design phase. Apart from power reduction, low-voltage operation will further extend the battery life. A 2.4GHz multi-standard radio is presented, as a test case, with an average power consumption in the µW range, and state-of-the-art performance across a voltage supply range from 1.2V to 0.9V.