Air discharge immunity testing for electronic equipment is specified in the standard 61000-4-2 of the International Eelectrotechnical Commission (IEC) under the climatic conditions of temperature (T) from 15 to 35 degrees Celsius and relative humidity (RH) from 30 to 60%. This implies that the air discharge testing is likely to provide significantly different test results due to the wide climatic range. To clarify effects of the above climatic conditions on air discharge testing, we previously measured air discharge currents from an electrostatic discharge (ESD) generator with test voltages from 2kV to 15kV at an approach speed of 80mm/s under 6 combinations of T and RH in the IEC specified range and non-specified climatic range. The result showed that the same absolute humidity (AH), which is determined by T and RH, provides almost the identical waveforms of the discharge currents despite different T and RH, and also that the current peaks at higher test voltages decrease as the AH increases. In this study, we further examine the combined effects of air discharges on test voltages, T, RH and AH with respect to two different approach speeds of 20mm/s and 80mm/s. As a result, the approach speed of 80mm/s is confirmed to provide the same results as the previous ones under the identical climatic conditions, whereas at a test voltage of 15kV under the IEC specified climatic conditions over 30% RH, the 20mm/s approach speed yields current waveforms entirely different from those at 80mm/s despite the same AH, and the peaks are basically unaffected by the AH. Under the IEC non-specified climatic conditions with RH less than 20%, however, the peaks decrease at higher test voltages as the AH increases. These findings obtained imply that under the same AH condition, at 80mm/s the air discharge peak is not almost affected by the RH, while at 20mm/s the lower the RH is, the higher is the peak on air discharge current.

How to restore virtual network against substrate network failure (e.g. link cut) is one of the key challenges of network virtualization. The traditional virtual network recovery (VNR) methods are mostly based on the idea of centralized control. However, if multiple virtual networks fail at the same time, their recovery processes are usually queued according to a specific priority, which may increase the average waiting time of users. In this letter, we study distributed virtual network recovery (DVNR) method to improve the virtual network recovery efficiency. We establish exclusive virtual machine (VM) for each virtual network and process recovery requests of multiple virtual networks in parallel. Simulation results show that the proposed DVNR method can obtain recovery success rate closely to centralized VNR method while yield ~70% less average recovery time.

Autonomous mobility machines, such as self-driving cars, transportation robots, and automated construction machines, are promising to support or enrich human lives. To further improve such machines, they will be connected to the network via wireless links to be managed, monitored, or remotely operated. The autonomous mobility machines must have self-status based on their positioning system to safely conduct their operations without colliding with other objects. The self-status is not only essential for machine operation but also it is valuable for wireless link quality management. This paper presents self-status-based wireless link quality prediction and evaluates its performance by using a prototype mobility robot combined with a wireless LAN system. The developed robot has functions to measure the throughput and receive signal strength indication and obtain self-status details such as location, direction, and odometry data. Prediction performance is evaluated in offline processing by using the dataset gathered in an indoor experiment. The experiments clarified that, in the 5.6 GHz band, link quality prediction using self-status of the robot forecasted the throughput several seconds into the future, and the prediction accuracies were investigated as dependent on time window size of the target throughput, bandwidth, and frequency gap.

The network load is increasing due to the spread of content distribution services. Caching is recognized as a technique to reduce the peak network load by storing popular content into memories of users. Coded caching is a new caching approach based on a carefully designed content placement to create coded multicasting opportunities. Coded caching schemes in single-rate networks are evaluated by the tradeoff between the size of memory and that of delivered data. For considering the network with multiple transmission rates, it is crucial how to operate multicast. In multicast delivery, a sender must communicate to intended receivers at a rate that is available to all receivers. Multicast scheduling method of determining rates to deliver are evaluated by throughput and delay in multi-rate wireless networks. In this paper, we discuss coded caching in the multi-rate wireless networks. We newly define a measure for evaluating the coded caching scheme as coded caching delay and propose a new coded caching scheme. Also, we compare the proposed coded caching scheme with conventional coded caching schemes and show that the proposed scheme is suitable for multi-rate wireless networks.

In emergency communication systems research, aerial wireless relay networks (AWRNs) using multicopter unmanned aerial vehicles (UAVs) have been proposed. The main issue of the AWRNs is how to minimize the delay time of packet transmissions since it is not easy to supply many multicopters to cover a wide area. In this paper, we review the flight schemes and their delay time for the AWRNs. Furthermore, the network has specific issues such as multicopters' drops due to their battery capacity depletion and inclination of moving multicopters. The inclination of multicopters affects the received power, and the communication range changes based on the inclination as well. Therefore, we clarify the effect of these issues on the delay time.

The impedance expansion method (IEM) is a circuit-modeling technique for electrically small devices based on the method of moments. In a previous study, a circuit model of a wireless power transfer (WPT) system was developed by utilizing the IEM and eigenmode analysis. However, this technique assumes that all the coupling elements (e.g., feeding loops and resonant coils) are in the absence of neighboring scatters (e.g., bodies of vehicles). This study extends the theory of the IEM to obtain the circuit model of a WPT system in the vicinity of a perfectly conducting scatterer (PCS). The numerical results show that the proposed method can be applied to the frequencies at which the dimension of the PCS is less than approximately a quarter wavelength. In addition, the yielded circuit model is found to be valid at the operating frequency band.

In this paper, we aim to develop technologies for the circuit fault diagnosis and propose a formulation of a measure of a test pattern for the circuit fault diagnosis. Given a faulty circuit, the fault diagnosis is to deduce locations of faults that had occurred in the circuit. The fault diagnosis is executed in software before the failure analysis by which engineers inspect physical defects, and helps to improve the manufacturing process which yielded faulty circuits. The heart of the fault diagnosis is to distinguish between candidate faults by using test patterns, which are applied to the circuit-under-diagnosis (CUD), and thus test patterns that can distinguish as many faults as possible need to be generated. This fact motivates us to consider the test pattern measure based on the number of fault-pairs that become distinguished by a test pattern. To the best of the authors' knowledge, that measure requires the computational time of complexity order O(NF2), where NF denotes the number of candidate faults. Since NF is generally large for real industrial circuits, the computational time of the measure is long even when a high-performance computer is used. The formulation proposed in this paper makes it possible to calculate the measure in the computational complexity of O(NF log NF), and thus that measure is useful for the test pattern selection in the fault diagnosis. In computational experiments, the effectiveness of the formulation is demonstrated as samples of computational times of the measure calculated by the traditional and the proposed formulae and thorough comparisons between several greedy heuristics which are based on the measure.

High level synthesis (HLS) is a source-code-driven Register Transfer Level (RTL) design tool, and the performance, the power consumption, and the area of a generated RTL are limited partly by the description of a HLS input source code. In order to break through such kind of limitation and to get a further optimized RTL, the optimization of the input source code is indispensable. Routing congestion is one of such problems we need to consider the refinement of a HLS input source code. In this paper, we propose a novel HLS flow that performs code improvements by detecting congested parts directly from HLS input source code without using physical logic synthesis, and regenerating the input source code for HLS. In our approach, the origin of the wire congestion is detected from the HLS input source code by applying pattern matching on Program-Dependence Graph (PDG) constructed from the HLS input source code, the possibility of wire congestion is reported.

This paper summarizes our recent studies on architecture, photonic integration, system validation and networking performance analysis of a flexible low-latency interconnect optical network switch (Flex-LIONS) for datacenter and high-performance computing (HPC) applications. Flex-LIONS leverages the all-to-all wavelength routing property in arrayed waveguide grating routers (AWGRs) combined with microring resonator (MRR)-based add/drop filtering and multi-wavelength spatial switching to enable topology and bandwidth reconfigurability to adapt the interconnection to different traffic profiles. By exploiting the multiple free spectral ranges of AWGRs, it is also possible to provide reconfiguration while maintaining minimum-diameter all-to-all interconnectivity. We report experimental results on the design, fabrication, and system testing of 8×8 silicon photonic (SiPh) Flex-LIONS chips demonstrating error-free all-to-all communication and reconfiguration exploiting different free spectral ranges (FSR0 and FSR1, respectively). After reconfiguration in FSR1, the bandwidth between the selected pair of nodes is increased from 50Gb/s to 125Gb/s while an all interconnectivity at 25Gb/s is maintained using FSR0. Finally, we investigate the use of Flex-LIONS in two different networking scenarios. First, networking simulations for a 256-node datacenter inter-rack communication scenario show the potential latency and energy benefits when using Flex-LIONS for optical reconfiguration based on different traffic profiles (a legacy fat-tree architecture is used for comparison). Second, we demonstrate the benefits of leveraging two FSRs in an 8-node 64-core computing system to provide reconfiguration for the hotspot nodes while maintaining minimum-diameter all-to-all interconnectivity.

Currently, the top-k error ratio is one of the primary methods to measure the accuracy of multi-category classification. Top-k multiclass SVM was designed to minimize the empirical risk based on the top-k error ratio. Two SDCA-based algorithms exist for learning the top-k SVM, both of which have several desirable properties for achieving optimization. However, both algorithms suffer from a serious disadvantage, that is, they cannot attain the optimal convergence in most cases owing to their theoretical imperfections. As demonstrated through numerical simulations, if the modified SDCA algorithm is employed, optimal convergence is always achieved, in contrast to the failure of the two existing SDCA-based algorithms. Finally, our analytical results are presented to clarify the significance of these existing algorithms.

Impact of sampling frequency and the number of quantization bit of analog-to-digital conversion (ADC) in a direct detection lightwave system using Kramers-Kronig (KK) relation, which has been attracting attention in recent years, are numerically investigated. We studied the effect of spectral broadening caused by nonlinear operations (logarithm, square root) of the KK algorithm when the frequency gap (shift frequency) between the modulated signal and the optical tone is varied. We found that reception performances depend on both the ADC bandwidth and the relative positions of the optical tone and the spectrum. Spectral broadening caused by the logarithm operation of the KK algorithm is found to be the dominant factor of signal distortion in an ADC bandwidth limited system. We studied the effect of the number of quantization bit on the error vector magnitude (EVM) of KK relation based reception in a carrier-to-signal power ratio (CSPR) adjustable transmission system. We found that performances of KK relation based receiver can be improved by increasing the number of quantization bits. For minimum-phase-condition satisfied KK receiver, the required number of quantization bit was found to be 5 bits or more for detection of QPSK, 16-QAM and 64-QAM-modulated signal after 20-km transmission.

We propose a new design approach to improve the computational efficiency of an optimal design of optical waveguide devices utilizing coupled mode theory (CMT) and a neural network (NN). Recently, the NN has begun to be used for efficient optimal design of optical devices. In this paper, the eigenmode analysis required in the CMT is skipped by using the NN, and optimization with an evolutionary algorithm can be efficiently carried out. To verify usefulness of our approach, optimal design examples of a wavelength insensitive 3dB coupler, a 1 : 2 power splitter, and a wavelength demultiplexer are shown and their transmission properties obtained by the CMT with the NN (NN-CMT) are verified by comparing with those calculated by a finite element beam propagation method (FE-BPM).

Communication networks for wide-scale distributed energy resources (DERs) including photovoltaics (PVs), wind, storage and battery systems and electric vehicles (EVs) will be indispensable in future power grids. In this paper, we compare optical fronthaul networks using existing optical ground wires (OPGWs) for centralized radio access network (C-RAN) architecture to realize cost effective wireless communication network expansion including low population area. We investigate the applicability of optical data transport technologies of physical layer split (PLS), analog radio-on-fiber (ARoF), and common public radio interface (CPRI). The deployment costs of them are comparatively analyzed. It was shown that physical layer split and analog radio-on-fiber with subcarrier multiplexing (SCM) result in lower cost than other technologies.

Authors had proposed a hybrid electromagnetic field analysis method suitable for an airport surface so far. In this paper, the hybrid method is validated by measurements by using a 1/50 scale-model of an airport considering several layouts of the buildings and sloping ground. The measured power distributions agreed with the analyzed ones within 5 dB errors excepting null points and the null positions of the distribution is also estimated within one wavelength errors.

For low-density parity-check (LDPC) codes, the penalized decoding method based on the alternating direction method of multipliers (ADMM) can improve the decoding performance at low signal-to-noise ratios and also has low decoding complexity. There are three effective methods that could increase the ADMM penalized decoding speed, which are reducing the number of Euclidean projections in ADMM penalized decoding, designing an effective penalty function and selecting an appropriate layered scheduling strategy for message transmission. In order to further increase the ADMM penalized decoding speed, through reducing the number of Euclidean projections and using the vertical layered scheduling strategy, this paper designs a fast converging ADMM penalized decoding method based on the improved penalty function. Simulation results show that the proposed method not only improves the decoding performance but also reduces the average number of iterations and the average decoding time.

A new structure of the electro-optic modulator to compensate the third-order intermodulation distortion (IMD3) is introduced. The modulator includes two Mach-Zehnder modulators (MZMs) operating with frequency chirp and the two modulated outputs are combined with an adequate phase difference. We revealed by theoretical analysis and numerical calculations that the IMD3 components in the receiver output could be selectively suppressed when the two MZMs operate with chirp parameters of opposite signs to each other. Spectral power of the IMD3 components in the proposed modulator was more than 15dB lower than that in a normal Mach-Zehnder modulator at modulation index between 0.15π and 0.25π rad. The IMD3 compensation properties of the proposed modulator was experimentally confirmed by using a dual parallel Mach-Zehnder modulator (DPMZM) structure. We designed and fabricated the modulator with the single-chip structure and the single-input operation by integrating with 180° hybrid coupler on the modulator substrate. Modulation signals were applied to each modulation electrode by the 180° hybrid coupler to set the chirp parameters of two MZMs of the DPMZM. The properties of the fabricated modulator were measured by using 10GHz two-tone signals. The performance of the IMD3 compensation agreed with that in the calculation. It was confirmed that the IMD3 compensation could be realized even by the fabricated modulator structure.

Recording source code changes comes to be well recognized as an effective means for understanding the evolution of existing software and making its future changes efficient. Therefore, modern integrated development environments (IDEs) tend to employ tools that record fine-grained textual changes of source code. However, there is still no satisfactory tool that accurately records textual changes. We propose ChangeMacroRecorder that automatically and silently records all textual changes of source code and in real time correlates those textual changes with actions causing them while a programmer is writing and modifying it on the Eclipse's Java editor. The improvement with respect to the accuracy of recorded textual changes enables both programmers and researchers to exactly understand how the source code was evolved. This paper presents detailed information on how ChangeMacroRecorder achieves the accurate recording of textual changes and demonstrates how accurate textual changes were recorded in our experiment consisting of nine programming tasks.

For actual multi-channel differential signaling system, the ideal balance or symmetrical topology cannot be established, and hence, an imbalance component is excited. However a theoretical analysis method of evaluating the voltage and current distribution on the differential-paired lines, which allows to anticipate EM radiation at the design stage and to study possible means for suppressing imbalance components, has not been implemented. To provide the basic considerations for electromagnetic (EM) radiation from practical asymmetrical differential-paired lines structure with equi-length routing used in high-speed board design, this paper newly proposes an analytical method for evaluating the voltage and current at any point on differential-paired lines by expressing the differential paired-lines with an equivalent source circuit and an equivalent load circuit. The proposed method can predict S-parameters, distributions of voltage and current and EM radiation with sufficient accuracy. In addition, the proposed method provides enough flexibility for different geometric parameters and can be used to develop physical insights and design guidelines. This study has successfully established a basic method to effectively predict signal integrity and EM interference issues on a differential-paired lines.

Silicon photonics technology is a promising candidate for small form factor transceivers that can be used in data-center applications. This technology has a small footprint, a low fabrication cost, and good temperature immunity. However, its main challenge is due to the high baud rate operation for optical modulators with a low power consumption. This paper investigates an all-Silicon Mach-Zehnder modulator based on the lumped-electrode optical phase shifters. These phase shifters are driven by a complementary metal oxide semiconductor (CMOS) inverter driver to achieve a low power optical transmitter. This architecture improves the power efficiency because an electrical digital-to-analog converter (DAC) and a linear driver are not required. In addition, the current only flows at the time of data transition. For this purpose, we use a PIN-diode phase shifter. These phase shifters have a large capacitance so the driving voltage can be reduced while maintaining an optical phase shift. On the other hand, this study integrates a passive resistance-capacitance (RC) equalizer with a PIN-phase shifter to expand the electro-optic (EO) bandwidth of a modulator. Therefore, the modulation efficiency and the EO bandwidth can be optimized by designing the capacitor of the RC equalizer. This paper reviews the recent progress for the high-speed operation of an all-Si PIN-RC modulator. This study introduces a metal-insulator-metal (MIM) structure for a capacitor with a passive RC equalizer to obtain a wider EO bandwidth. As a result, this investigation achieves an EO bandwidth of 35.7-37 GHz and a 70 Gbaud NRZ operation is confirmed.

We review our research progress of multi-port optical switches based on the silicon photonics platform. Up to now, the maximum port-count is 32 input ports×32 output ports, in which transmissions of all paths were demonstrated. The switch topology is path-independent insertion-loss (PILOSS) which consists of an array of 2×2 element switches and intersections. The switch presented an average fiber-to-fiber insertion loss of 10.8 dB. Moreover, -20-dB crosstalk bandwidth of 14.2 nm was achieved with output-port-exchanged element switches, and an average polarization-dependent loss (PDL) of 3.2 dB was achieved with a non-duplicated polarization-diversity structure enabled by SiN overpass waveguides. In the 8×8 switch, we demonstrated wider than 100-nm bandwidth for less than -30-dB crosstalk with double Mach-Zehnder element switches, and less than 0.5 dB PDL with polarization diversity scheme which consisted of two switch matrices and fiber-type polarization beam splitters. Based on the switch performances described above, we discuss further improvement of switching performances.