Xiuping PENG Yinna LIU Hongbin LIN
In this letter, we propose a novel direct construction of three-phase Z-complementary triads with flexible lengths and various widths of the zero-correlation zone based on extended Boolean functions. The maximum width ratio of the zero-correlation zone of the construction can reach 3/4. And the proposed sequences can exist for all lengths other than powers of three. We also investigate the peak-to-average power ratio properties of the proposed ZCTs.
We propose a zero-order-hold triggered control for a chain of integrators with an arbitrary sampling period. We analytically show that our control scheme globally asymptotically stabilizes the considered system. The key feature is that the pre-specified sampling period can be enlarged as desired by adjusting a gain-scaling factor. An example with various simulation results is given for clear illustration.
Hiroshi SUENOBU Shin-ichi YAMAMOTO Michio TAKIKAWA Naofumi YONEDA
A method for bandwidth enhancement of radar cross section (RCS) reduction by metasurfaces was studied. Scattering cancellation is one of common methods for reducing RCS of target scatterers. It occurs when the wave scattered by the target scatterer and the wave scattered by the canceling scatterer are the same amplitude and opposite phase. Since bandwidth of scattering cancellation is usually narrow, we proposed the bandwidth enhancement method using metasurfaces, which can control the frequency dependence of the scattering phase. We designed and fabricated a metasurface composed of a patch array on a grounded dielectric substrate. Numerical and experimental evaluations confirmed that the metasurface enhances the bandwidth of 10dB RCS reduction by 52% bandwidth ratio of the metasurface from 34% bandwidth ratio of metallic cancelling scatterers.
Peijian ZHANG Kunfeng ZHU Wensuo CHEN
In this paper, a novel trench MOS barrier Schottky contact super barrier rectifier (TMB-SSBR) is proposed by combining the advantages of vertical SSBR and conventional TMBS. The operation mechanism and simulation verification are presented. TMB-SSBR consists of MOS trenches with a vertical SSBR grid which replaces the Schottky diode in the mesa of a TMBS. Due to the presence of top p-n junction in the proposed TMB-SSBR, the image force barrier lowering effect is eliminated, the pinching off electric field effect by MOS trenches is weakened, so that the mesa surface electric field is much larger than that in conventional TMBS. Therefore, the mesa width is enlarged and the n-drift concentration is slightly increased, which results in a low specific on-resistance and a good tradeoff between reverse leakage currents and forward voltages. Compared to a conventional TMBS, simulation results show that, with the same breakdown voltage of 124V and the same reverse leakage current at room temperature, TMB-SSBR increases the figure of merit (FOM, equates to VB2/Ron, sp) by 25.5%, and decreases the reverse leakage by 33.3% at the temperature of 423K. Just like the development from SBD to TMBS, from TMBS to TMB-SSBR also brings obvious improvement of performance.
A novel charge pump, Capacitance Varying Charge Pump (CVCP) is proposed. This charge pump is composed of variable capacitors and rectifiers, and the charge transfer is attained by changing the capacitance values in a manner similar to peristaltic pumps. The analysis of multi-stage CVCP reveals that the output voltage is exponentially dependent on the stage number. Thus, compared with the Dickson charge pump, this charge pump has an advantage in generating high voltages with small stages. As a practical example of CVCP, we present an implementation realized by a MEMS (Micro-Electro-Mechanical Systems) technology. Here, the variable capacitor is enabled by a comb-capacitor attached to a high-quality factor resonator. As the rectifier, a PN-junction diode formed in the MEMS layer is used. Simulations including the mechanical elements are carried out for this MEMS version of CVCP. The simulation results on the output voltage and load characteristics are shown to coincide well with the theoretical estimations. The MEMS CVCP is suited for MEMS devices and vibration energy harvesters.
Shinya MATSUFUJI Sho KURODA Yuta IDA Takahiro MATSUMOTO Naoki SUEHIRO
A set consisting of K subsets of Msequences of length L is called a complementary sequence set expressed by A(L, K, M), if the sum of the out-of-phase aperiodic autocorrelation functions of the sequences within a subset and the sum of the cross-correlation functions between the corresponding sequences in any two subsets are zero at any phase shift. Suehiro et al. first proposed complementary set A(Nn, N, N) where N and n are positive integers greater than or equal to 2. Recently, several complementary sets related to Suehiro's construction, such as N being a power of a prime number, have been proposed. However, there is no discussion about their inclusion relation and properties of sequences. This paper rigorously formulates and investigates the (generalized) logic functions of the complementary sets by Suehiro et al. in order to understand its construction method and the properties of sequences. As a result, it is shown that there exists a case where the logic function is bent when n is even. This means that each series can be guaranteed to have pseudo-random properties to some extent. In other words, it means that the complementary set can be successfully applied to communication on fluctuating channels. The logic functions also allow simplification of sequence generators and their matched filters.
This paper focuses on a pseudorandom number generator called an NTU sequence for use in cryptography. The generator is defined with an m-sequence and Legendre symbol over an odd characteristic field. Since the previous researches have shown that the generator has maximum complexity; however, its bit distribution property is not balanced. To address this drawback, the author introduces dynamic mapping for the generation process and evaluates the period and some distribution properties in this paper.
Even correlation and odd correlation of sequences are two kinds of measures for their similarities. Both kinds of correlation have important applications in communication and radar. Compared with vast knowledge on sequences with good even correlation, relatively little is known on sequences with preferable odd correlation. In this paper, a generic construction of sequences with low odd correlation is proposed via interleaving technique. Notably, it can generate new sets of binary sequences with optimal odd correlation asymptotically meeting the Sarwate bound.
Xiaoyu CHEN Yihan ZHANG Lianfeng SUN Yubo LI
This letter is devoted to constructing new Type-II Z-complementary pairs (ZCPs). A ZCP of length N with ZCZ width Z is referred to in short by the designation (N, Z)-ZCP. Inspired by existing works of ZCPs, systematic constructions of (2N+3, N+2)-ZCPs and (4N+4, 7/2N+4)-ZCPs are proposed by appropriately inserting elements into concatenated GCPs. The odd-length binary Z-complementary pairs (OB-ZCPs) are Z-optimal. Furthermore, the proposed construction can generate even-length binary Z-complementary pairs (EB-ZCPs) with ZCZ ratio (i.e. ZCZ width over the sequence length) of 7/8. It turns out that the PMEPR of resultant EB-ZCPs are upper bounded by 4.
Aya KOYAMA Yosuke TANIGAWA Hideki TODE
Nowadays, in various wireless sensor networks, both aperiodically generated packets like event detections and periodically generated ones for environmental, machinery, vital monitoring, etc. are transferred. Thus, packet loss caused by collision should be suppressed among aperiodic and periodic packets. In addition, some packets for wireless applications such as factory IoT must be transferred within permissible end-to-end delays, in addition to improving packet loss. In this paper, we propose transmission timing control of both aperiodic and periodic packets at an upper layer of medium access control (MAC). First, to suppress packet loss caused by collision, transmission timings of aperiodic and periodic packets are distributed on the time axis. Then, transmission timings of delay-bounded packets with permissible delays are assigned within the bounded periods so that transfer within their permissible delays is possible to maximally satisfy their permissible delays. Such control at an upper layer has advantages of no modification to the MAC layer standardized by IEEE 802.11, 802.15.4, etc. and low sensor node cost, whereas existing approaches at the MAC layer rely on MAC modifications and time synchronization among all sensor nodes. Performance evaluation verifies that the proposed transmission timing control improves packet loss rate regardless of the presence or absence of packet's periodicity and permissible delay, and restricts average transfer delay of delay-bounded packets within their permissible delays comparably to a greedy approach that transmits delay-bounded packets to the MAC layer immediately when they are generated at an upper layer.
Koichi NARAHARA Koichi MAEZAWA
Series-connection of resonant-tunneling diodes (RTDs) has been considered to be efficient in upgrading the output power when it is introduced to oscillator architecture. This work is for clarifying the same architecture also contributes to increasing oscillation frequency because the device parasitic capacitance is reduced M times for M series-connected RTD oscillator. Although this mechanism is expected to be universal, we restrict the discussion to the recently proposed multiphase oscillator utilizing an RTD oscillator lattice loop. After explaining the operation principle, we evaluate how the oscillation frequency depends on the number of series-connected RTDs through full-wave calculations. In addition, the essential dynamics were validated experimentally in breadboarded multiphase oscillators using Esaki diodes in place of RTDs.
Satomitsu IMAI Kazuki CHIDAISYO Kosuke YASUDA
Incorporating a tool for administering medication, such as a syringe, is required in microneedles (MNs) for medical use. This renders it easier for non-medical personnel to administer medication. Because it is difficult to fabricate a hollow MN, we fabricated a capillary groove on an MN and its substrate to enable the administration of a higher dosage. MN grooving is difficult to accomplish via the conventional injection molding method used for polylactic acid. Therefore, biodegradable polyacid anhydride was selected as the material for the MN. Because polyacid anhydride is a low-viscosity liquid at room temperature, an MN can be grooved using a processing method similar to vacuum casting. This study investigated the performance of the capillary force of the MN and the optimum shape and size of the MN by a puncture test.
Umer FAROOQ Masayuki MORI Koichi MAEZAWA
We achieved detailed characterization of resonant tunneling chaos generator circuits in microwave frequency range. The circuit is analogous to Duffing oscillator, where the third-order nonlinear potential term is emulated by the nonlinear current-voltage curve of the resonant tunneling diode. The circuit includes a periodic reset mechanism to output identical chaos signal, which is essential to observe chaos signal on a sampling oscilloscope. Though this was shown to be effective in our previous papers, the length of the waveforms to observe is limited to rather short period, and it was unclear if this technique can be used for detailed characterization of such high-frequency chaos. In this paper, we improved the circuit design to observe longer waveforms, and demonstrated that the detailed characterization is possible using this periodic resetting technique with a sampling oscilloscope. The hybrid integration scheme is also used in this paper, which allows the easiest and shortest way to mimic a circuit as per circuit design, and precise estimation of circuit parameters aiming to eliminate circuit-related abnormalities. We provide deep insight into the dynamics associated with our circuit, starting from the single period, double period, chaos, and triple period regimes, by extracting power spectra, return maps, phase portraits, and bifurcation diagrams from acquired time series using sampling oscilloscope. Our method to study microwave chaotic signals can be applied to much higher frequency ranges, such as THz frequency range.
Katsumi KAWAI Naoki SHINOHARA Tomohiko MITANI
This study proposes a new structure of a single-shunt rectifier circuit that can reduce circuit loss and improve efficiency over the conventional structure. The proposed structure can provide impedance matching to the measurement system (or receiving antenna) without the use of conventional matching circuits, such as stubs and tapers. The proposed structure can simultaneously perform full-wave rectification and impedance matching by placing a feeding point on the output filter's λ/4 transmission line. We use circuit simulation to compare the RF-DC conversion efficiency and circuit loss of the conventional and proposed structures. The simulation results show that the proposed structure has lower circuit loss and higher RF-DC conversion efficiency than the conventional structure. We fabricate the proposed rectifier circuit using a GaAs Schottky barrier diode. The simulation and measurement results show that the single-shunt rectifier circuit's proposed structure is capable of rectification and impedance matching. The fabricated rectifier circuit's RF-DC conversion efficiency reaches a maximum of 91.0%. This RF-DC conversion efficiency is a world record for 920-MHz band rectifier circuits.
Kosuke OHARA Hirohisa AMAN Sousuke AMASAKI Tomoyuki YOKOGAWA Minoru KAWAHARA
This paper focuses on the “data collection period” for training a better Just-In-Time (JIT) defect prediction model — the early commit data vs. the recent one —, and conducts a large-scale comparative study to explore an appropriate data collection period. Since there are many possible machine learning algorithms for training defect prediction models, the selection of machine learning algorithms can become a threat to validity. Hence, this study adopts the automatic machine learning method to mitigate the selection bias in the comparative study. The empirical results using 122 open-source software projects prove the trend that the dataset composed of the recent commits would become a better training set for JIT defect prediction models.
Kenji ITOH Naoki SAKAI Keisuke NOGUCHI
In this paper, a high-efficiency high-power rectenna with a bridge diode and the diode on antenna (DoA) topology is discussed. First, the topologies of rectifiers and rectennas are discussed to indicate the direction for obtaining highly efficient rectification. Rectifiers with well-matched diode pairs, as double voltage and bridge rectifiers, can reactively terminate even order harmonics, and is suitable for highly efficient operation. A rectenna with the DoA topology is suitable for a direct connection between the highly functional antenna and the rectifier diodes to remove lossy circuit portions. Next, the formulas for the rectification efficiency of the bridge rectifier are demonstrated with the behavioral model. The indicated formulas clarify the fundamental limitation on the rectification efficiency, which is the design goal in case of the DoA topology. Finally, we demonstrate a 5.8 GHz band 1 W rectenna with the bridge diode and the DoA topology. The bridge rectifier that is directly connected to the inductive high-impedance antenna achieved a rectification efficiency of 92.8% at an input power of 1 W. This is close to the fundamental limitation due to the diode performance.
Kotaro AIKAWA Michihiko SUHARA Takumi KIMURA Junki WAKAYAMA Takeshi MAKINO Katsuhiro USUI Kiyoto ASAKAWA Kouichi AKAHANE Issei WATANABE
S-parameters of InGaAs/InAlAs triple-barrier resonant tunneling diodes (TBRTDs) were measured up to 67 GHz with various mesa areas and various bias voltages. Admittance data of bare TBRTDs are deembedded and evaluated by getting rid of parasitic components with help of electromagnetic simulations for particular fabricated device structures. Admittance spectroscopy up to 67 GHz is applied for bare TBRTDs for the first time and a Kramers-Kronig relation with Lorentzian function is found to be a consistent model for the admittance especially in cases of low bias conditions. Relaxation time included in the Lorentzian function are tentatively evaluated as the order of several pico second.
This paper proposes a novel interference cancellation technique that prevents radio receivers from degrading due to periodic interference signals caused by electromagnetic waves emitted from high power circuits. The proposed technique cancels periodic interference signals in the frequency domain, even if the periodic interference signals drift in the time domain. We propose a drift estimation based on a super resolution technique such as ESPRIT. Moreover, we propose a sequential drift estimation to enhance the drift estimation performance. The proposed technique employs a linear filter based on the minimum mean square error criterion with assistance of the estimated drifts for the interference cancellation. The performance of the proposed technique is confirmed by computer simulation. The proposed technique achieves a gain of more than 40dB at the higher frequency part in the band. The proposed canceler achieves such superior performance, if the parameter sets are carefully selected. The proposed sequential drift estimation relaxes the parameter constraints, and enables the proposed cancellation to achieve the performance upper bound.
Tao YU Yang YANG Hua MENG Yong WANG
Almost-complementary pairs (ACPs) are sequence pairs whose autocorrelations sum up to zero at all but one non-zero time-shifts. Periodic ACPs (P-ACPs) display almost similar correlation properties to that of the periodic complementary pairs (PCPs). In this letter, we propose systematic constructions of quadriphase P-ACPs (QP-ACPs) from aperiodic (periodic) complementary pairs and almost perfect binary (quadriphase) sequences. The proposed construction gives QP-ACPs of new lengths which are not covered in the literature.
Shimpei SHIMIZU Takayuki KOBAYASHI Takeshi UMEKI Takushi KAZAMA Koji ENBUTSU Ryoichi KASAHARA Yutaka MIYAMOTO
Optical phase conjugation (OPC) is an all-optical signal processing technique for mitigating fiber nonlinearity and is promising for building cost-efficient fiber networks with few optic-electric-optic conversions and long amplification spacing. In lumped amplified systems, OPC has a little nonlinearity mitigation efficiency for nonlinear distortion induced by cross-phase modulation (XPM) due to the asymmetry of power and chromatic dispersion (CD) maps during propagation in transmission fiber. In addition, the walk-off of XPM-induced noise becomes small due to the CD compensation effect of OPC, so the deterministic nonlinear distortion increases. Therefore, lumped amplified transmission systems with OPC are more sensitive to channel spacing than conventional systems. In this paper, we show the channel spacing dependence of NZ-DSF transmission using amplification repeater with OPC. Numerical simulations show comprehensive characteristics between channel spacing and CD in a 100-Gbps/λ WDM signal. An experimental verification using periodically poled LiNbO3-based OPC is also performed. These results suggest that channel spacing design is more important in OPC-assisted systems than in conventional dispersion-unmanaged systems.