An optoelectronic 32-bit serial-to-parallel converter with a novel conversion scheme and shared-trigger configuration has been developed for the label processing of 100-Gbps (25-Gbps $ imes 4 lambda)$ optical packets. No external optical trigger source is required to operate the converter, as the optical packet itself is used to perform self-triggering. Compared to prior optoelectronic label converters, the new device has a much higher gain even while converting labels at higher data rates, and exhibits tolerance to the voltage swing of received packets. The device response is presented together with the experimental demonstration of serial-to-parallel conversion for 4 different labels at 25 Gbps.

This paper introduces a partially parallel inter-chip link architecture for asynchronous multi-chip Network-on-Chips (NoCs). The multi-chip NoCs that operate as a large NoC have been recently proposed for very large systems, such as automotive applications. Inter-chip links are key elements to realize high-performance multi-chip NoCs using a limited number of I/Os. The proposed asynchronous link based on level-encoded dual-rail (LEDR) encoding transmits several bits in parallel that are received by detecting the phase information of the LEDR signals at each serial link. It employs a burst-mode data transmission that eliminates a per-bit handshake for a high-speed operation, but the elimination may cause data-transmission errors due to cross-talk and power-supply noises. For triggering data retransmission, errors are detected from the embedded phase information; error-detection codes are not used. The throughput is theoretically modelled and is optimized by considering the bit-error rate (BER) of the link. Using delay parameters estimated for a 0.13 µm CMOS technology, the throughput of 8.82 Gbps is achieved by using 10 I/Os, which is 90.5% higher than that of a link using 9 I/Os without an error-detection method operating under negligible low BER (<10-20).

Optical processing of optical labels is expected for increasing processing speed in network routers. We previously proposed optical waveguide circuits for recognition of optical QAM codes by detecting a null output port. The circuits are based on a recognition circuit for QPSK codes. In the device, however, optical or electrical inverters with large dynamic range are required. In this paper, we propose optical circuits to recognize optical QAM codes by maximum output with a post-processor consisting of thresholders and logical circuits. The recognition function of the waveguide circuit is numerically proved by FD BPM.

A new algorithm is proposed for finding all solutions of piecewise-linear resistive circuits using separable programming. In this algorithm, the problem of finding all solutions is formulated as a separable programming problem, and it is solved by the modified simplex method using the restricted-basis entry rule. Since the modified simplex method finds one solution per application, the proposed algorithm can find all solutions efficiently. Numerical examples are given to confirm the effectiveness of the proposed algorithm.

A 125MHz 64-phase delay-locked loop (DLL) is implemented for time recovery in a digital wire-line system. The architecture of the proposed DLL comprises a coarse-locking circuit added to a conventional DLL circuit, which consists of a delay line including a bias circuit, phase detector, charge pump, and loop filter. The proposed coarse-locking circuit reduces the locking time of the DLL and prevents harmonic locking, regardless of the duty cycle of the clock. In order to verify the performance of the proposed coarse-locking circuit, a 64-phase DLL with an operating frequency range of 40 to 200MHz is fabricated using a 0.18-µm 1-poly 6-metal CMOS process with a 1.8V supply. The measured rms and peak-to-peak jitter of the output clock are 3.07ps and 21.1ps, respectively. The DNL and INL of the 64-phase output clock are measured to be -0.338/+0.164 LSB and -0.464/+0.171 LSB, respectively, at an operating frequency of 125MHz. The area and power consumption of the implemented DLL are 0.3mm2 and 12.7mW, respectively.

An energy-efficient ΔΣ modulator using a novel switched-capacitor-based integrator has been investigated. The proposed dynamic integrator uses a common-source configuration, where a MOSFET turns off after the charge redistribution is completed. Thus, only the subthreshold current flows through the integrator, resulting in high energy efficiency. A constant threshold voltage works as the virtual ground in conventional opamp-based integrators. The performance has been estimated for a 2nd-order ΔΣ modulator by transistor-level circuit simulation assuming a 0.18-µm standard CMOS technology. An FOM of 29fJ/conv-step was obtained with a peak SNDR of 82.6dB for a bandwidth and a sampling frequency of 20kHz and 5MHz, respectively.

The authors have evaluated a method of expanding the bit depth of image signals called SGRAD, which requires fewer calculations, while degrading the sharpness of images less. Where noise is superimposed on image signals, the conventional method for obtaining high bit depth sometimes incorrectly detects the contours of images, making it unable to sufficiently correct the gradation. Requiring many line memories is also an issue with the conventional method when applying the process to vertical gradation. As a solution to this particular issue, SGRAD improves the method of detecting contours with transiting gradation to effectively correct the gradation of image signals which noise is superimposed on. In addition, the use of a prediction algorithm for detecting gradation reduces the scale of the circuit with less correction of the vertical gradation.

Hassoune and O'Connor proposed a dynamically reconfigurable dynamic logic circuit (DRDLC) that generates Boolean functions by using double-gate (DG) carbon nanotube (CNT) FETs, which have an ambipolar property. O'Connor et al. proposed a DRDLC that generates 14 Boolean functions asing two Boolean inputs with seven transistors. Furthermore, DRDLCs that generates all 16 Boolean functions have been proposed. In this paper, we focus on the design of a dynamic logic circuit with n Boolean inputs. First, we show a DRDLC that generates the monomial Boolean functions. Next, we propose a DRDLC that generates the whole set of Boolean functions consisting of t terms or less. Finally, we report the number of Boolean functions generated by the proposed DRDLC.

Homotopy methods are known to be effective methods for finding DC operating points of nonlinear circuits with the theoretical guarantee of global convergence. There are several types of homotopy methods; as one of the most efficient methods for solving bipolar transistor circuits, the variable-gain homotopy (VGH) method is well-known. In this paper, we propose an efficient VGH method for solving bipolar and MOS transistor circuits. We also show that the proposed method converges to a stable operating point with high possibility from any initial point. The proposed method is not only globally convergent but also more efficient than the conventional VGH methods. Moreover, it can easily be implemented in SPICE.

This paper gives a write voltage and read reference current generator considering temperature characteristics for multi-level Ge2Sb2Te5-based phase change memories. Since the optimum SET and RESET voltages linearly changes by the temperature, the voltage supply circuit must track this characteristic. In addition, the measurement results show that the read current depends on both read temperature and the write temperature and has exponential dependence on the read temperature. Thus, the binning technique is applied for each read and write temperature regions. The proposed variable TC generator can achieve below ±0.5 LSB precision from the measured differential non-linearity and integral non-linearity. As a result, the temperature characteristics of both the linear write voltage and the exponential read current can be tracked with the proposed variation tolerant linear temperature coefficient current generator.

A modern system-on-chip (SoC) includes many heterogeneous IP components. Generally, a few embedded processors are integrated into SoCs. An asynchronous circuit design technique is employed to achieve low power/energy consumption. In this paper, we design an asynchronous embedded processor on FPGAs and analyze its possible benefits on commercial FPGAs. We use commercially available 65nm high-performance Virtex-5 and 45nm low-power Spartan-6 Xilinx FPGAs to show the impact on power consumption for the two different extreme cases. For the high performance Virtex-5, our asynchronous processor shows 36.8% lower power consumption when compared with its synchronous counterpart. On the other hand, the asynchronous processor consumes 25.6% more power in a low power Spartan-6 FPGA. However, through simple analysis and power simulation, we show that the event-driven nature of asynchronous circuits can further save power/energy even in the Spartan-6 FPGA.

We propose an improved design of a neuron circuit, using coupled SQUIDs gates, for a superconducting neural network. An activation function with step-like input vs. output characteristics is desirable for a neuron circuit to solve a combinatorial optimization problem. The proposed neuron circuit is composed of two coupled SQUIDs gates with a cascade connection, in order to obtain such characteristics. The designed neuron circuit is fabricated by a 2.5kA/cm2 Nb/AlOx/Nb process. The operation of a fabricated neuron circuit is experimentally demonstrated. Network performance of a neural network using proposed neuron circuits is also estimated by numerical dynamic simulations.

We have been developing a superconducting time-of-flight mass spectrometry (TOF-MS) system, which utilizes a superconductive strip ion detector (SSID) and a single-flux-quantum (SFQ) multi-stop time-to-digital converter (TDC). The SFQ multi-stop TDC can measure the time intervals between multiple input signals and directly convert them into binary data. In this study, we designed and implemented 24-bit SFQ multi-stop TDCs with a 3×24-bit FIFO buffer using the AIST Nb standard process (STP2), whose time resolution and dynamic range are 100ps and 1.6ms, respectively. The timing jitter of the TDC was investigated by comparing two types of TDCs: one uses an on-chip SFQ clock generator (CG) and the other uses a microwave oscillator at room temperature. We confirmed the correct operation of both TDCs and evaluated their timing jitter. The experimentally-obtained timing jitter is about 40ns and 700ps for the TDCs with and without the on-chip SFQ CG, respectively, for the measured time interval of 50µs, which linearly increases with increase of the measured time interval.

We present our design and operation of a 6-bit quasi-triangle voltage waveform generator comprising three circuit blocks; an improved variable Pulse Number Multiplier (variable-PNM), a Code Generator (CG), and a Double-Flux-Quantum Amplifier (DFQA). They are integrated into a single chip using a niobium Josephson junction technology. While the multiplication factor of our previous m-bit variable-PNM was limited between 2m-1 and 2m, that of the improved one is extended between 1 and 2m. Correct operations of the 6-bit variable-PNM are confirmed in low-speed testing with respect to the codes from the CG, whereas generation of a 6-bit, 0.20mVpp quasi-triangle voltage waveform is demonstrated with the 10-fold DFQA in high-speed testing.

We describe a large-scale integrated circuit (LSI) design of rapid single-flux-quantum (RSFQ) circuits and demonstrate several reconfigurable data-path (RDP) processor prototypes based on the ISTEC Advanced Process (ADP2). The ADP2 LSIs are made up of nine Nb layers and Nb/AlOx/Nb Josephson junctions with a critical current density of 10kA/cm2, allowing higher operating frequencies and integration. To realize truly large-scale RSFQ circuits, careful design is necessary, with several compromises in the device structure, logic gates, and interconnects, balancing the competing demands of integration density, design flexibility, and fabrication yield. We summarize numerical and experimental results related to the development of a cell-based design in the ADP2, which features a unit cell size reduced to 30-µm square and up to four strip line tracks in the unit cell underneath the logic gates. The ADP LSIs can achieve ∼10 times the device density and double the operating frequency with the same power consumption per junction as conventional LSIs fabricated using the Nb four-layer process. We report the design and test results of RDP processor prototypes using the ADP2 cell library. The RDP processors are composed of many arrays of floating-point units (FPUs) and switch networks, and serve as accelerators in a high-performance computing system. The prototypes are composed of two-dimensional arrays of several arithmetic logic units instead of FPUs. The experimental results include a successful demonstration of full operation and reconfiguration in a 2×2 RDP prototype made up of 11.5k junctions at 45GHz after precise timing design. Partial operation of a 4×4 RDP prototype made up of 28.5k-junctions is also demonstrated, indicating the scalability of our timing design.

Recently, we proposed a new data-path architecture, named a large-scale reconfigurable data-path (LSRDP), based on single-flux-quantum (SFQ) circuits, to establish a fundamental technology for future high-end computers. In this architecture, a large number of SFQ floating-point units (FPUs) are used as core components, and their high performance and low power consumption are essential. In this research, we implemented an SFQ half-precision bit-serial floating-point multiplier (FPM) with a target clock frequency of 50GHz, using the AIST 10kA/cm2 Nb process. The FPM was designed, based on a systolic-array architecture. It contains 11,066 Josephson junctions, including on-chip high-speed test circuits. The size and power consumption of the FPM are 6.66mm × 1.92mm and 2.83mW, respectively. Its correct operation was confirmed at a maximum frequency of 93.4GHz for the exponent part and of 72.0GHz for the significand part by on-chip high-speed tests.

Superconducting Single-Flux-Quantum (SFQ) devices have been paid much attention as alternative devices for digital circuits, because of their high switching speed and low power consumption. For large-scale circuit design, the role of computer-aided design environment is significant. As the characteristics of the SFQ devices are different from conventional devices, a new design environment is required. In this paper, we propose a new timing-aware circuit description method which can be used for SFQ circuit design. Based on the description and the dedicated algorithms we have been developing for SFQ logic circuit design, we propose an integrated design flow for SFQ logic circuits. We have designed a circuit using our developed design tools along with the design flow and demonstrated the correct operation.

A promising application of a single-flux quantum (SFQ) circuit is read-out circuitry for a multi-channel superconductive sensor array. In such applications, the SFQ read-out circuit is expected to operate outside a magnetic shield. We investigated an SFQ circuit structure, which is tolerant to an external magnetic field, using the AIST 2.5kA/cm2 Nb standard 2 process, which has four Nb wiring layers including the ground plane. By covering the entire circuit using an upper Nb wiring layer called the control (CTL) layer, the influences of the external magnetic field on the SFQ circuit operation can be avoided. We experimentally evaluated the sheet inductance of the wiring layer underneath the CTL shielding layer to design a magnetic-field-tolerant SFQ circuit. We implemented and measured test circuits comprising toggle flip-flops (TFFs) to evaluate their magnetic field tolerances. The operating margin and maximum operating frequency of the designed TFF did not deteriorate with increases in the magnetic field applied to the test circuit, whereas the operating margin of the conventional TFF was reduced by applying the magnetic field. We have also demonstrated the high-speed operation of the designed TFF operated in an unshielded environment at a frequency of up to 120GHz with a wide operating margin.

This letter describes a design methodology for an arithmetic logic unit (ALU) incorporating reconfigurability based on double-gate carbon nanotube field-effect transistors (DG-CNTFETs). The design of a DG-CNTFET with an ambipolar-property-based reconfigurable static logic circuit is simple and straightforward using an ambipolar binary decision diagram (Am-BDD), which represents the cornerstone for the automatic pass transistor logic (PTL) synthesis flows of ambipolar devices. In this work, an ALU with 16 functions is synthesized by the design methodology of a DG-CNTFET-based reconfigurable static logic circuit. Furthermore, it is shown that the proposed ALU is much more flexible and practical than a conventional DG-CNTFET-based reconfigurable ALU.

In this paper, the measurement of capacitance variation, of an on-chip power distribution network (PDN) due to the change of internal states of a CMOS logic circuit, is studied. A state-dependent PDN-capacitance model that explains measurement results will be also proposed. The model is composed of capacitance elements related to MOS transistors, signal and power supply wires, and substrate. Reflecting the changes of electrode potentials, the capacitance elements become state-dependent. The capacitive elements are then all connected in parallel between power supply and ground to form the proposed model. By using the proposed model, state-dependence of PDN-capacitances for different logic circuits are studied in detail. The change of PDN-capacitance exceeds 12% of its total capacitance in some cases, which corresponds to 6% shift of anti-resonance frequency. Consideration of the state-dependence is important for modeling the PDN-capacitance.