Synthesis of quantum circuits is essential for building quantum computers. It is important to verify that the circuits designed perform the correct functions. In this paper, we propose an algorithm which can be used to verify the quantum circuits synthesized by any method. The proposed algorithm is based on BDD (Binary Decision Diagram) and is called X-decomposition Quantum Decision Diagram (XQDD). In this method, quantum operations are modeled using a graphic method and the verification process is based on comparing these graphic diagrams. We also develop an algorithm to verify reversible circuits even if they have a different number of garbage qubits. In most cases, the number of nodes used in XQDD is less than that in other representations. In general, the proposed method is more efficient in terms of space and time and can be used to verify many quantum circuits in polynomial time.

A current-mode squarer/divider circuit with a novel translinear cell is presented for automotive applications. The proposed circuit technique increases the accuracy of the squarer/divider function with better input dynamic range and temperature insensitivity. Simulation results show that the variation of the output current is within ±0.2% over the temperature range from -40 to 140.

A multi-path structure is proposed for reduction in effect of digital substrate noise which degrades analog circuit performance. As an example low-pass filters are implemented in a 0.18-µm CMOS process. 11-dBm reduction in digital substrate noise is achieved as compared with a conventional structure.

A power-efficient Dickson-based charge pump circuit is proposed and verified in this paper. Using a PMOS transfer switch in the new circuit solves the problem of the output voltage loss and its body control switch can suppress the parasitic bipolar action. Comparing this new one with the conventional circuit, the new circuit generates output voltage as high as 2.9 VDD while the conventional one only 2 VDD. For their efficiency values, the new circuit has better efficiency than the conventional one by as much as 14.5% with the area overhead of 12.2% using 3.5-µm and 40-V CMOS high-voltage process.

This paper discusses the input range limitation problem in a track-and-hold circuit and the compensation method using a bootstrapped switch. A bootstrapped switch with an additional control circuit is proposed to compensate charge loss in conventional bootstrapped switch circuit. Simulation results using 0.18-µm CMOS process parameters show that the proposed circuit reduces the bootstrap capacitance down to 25% for the conventional circuit.

For real time image processing, a readout circuit for an infrared focal plane array (IRFPA) involving a new edge detection technique has been proposed in this letter. A non-uniformity correction unit (NUC), essential in an IRFPA because of bad non-uniformity characteristics of IR sensors is eliminated in this circuit by using a noise tolerant edge detection technique. In addition, real time edge detection can be possible, because of pixel-level integration and parallel processing. The proposed readout circuit shows an approximately three to nine times better edge error rate than other available methods using pixel-level parallel processing.

In recent years, some countermeasures have been proposed against differential power analysis (DPA) at the basic composition element level of logic circuits. We propose a countermeasure named random switching logic (RSL). RSL involves computation with data masking using a single logic gate and suppression of transient transitions using ENABLE signals generated independently of input data. Recently, some countermeasures that were proposed against DPA, such as MRSL and DRSL, adopted the concept of RSL. Although MRSL is based on RSL, it uses a different method to suppress the transient transitions. DRSL uses RSL to avoid the possibility of leakage caused by a difference in delays occurring in MDPL that combines dual-rail circuits with random masking. The important difference between these countermeasures and RSL is that they can vary the output transition timing depending on the input data patterns. In this paper, we focus on this feature to evaluate the DPA resistance of MRSL and DRSL. Experiments are also conducted on DPA resistance by using an FPGA to verify the evaluation results. It is confirmed that in both MRSL and DRSL, there is a possibility of leakage if a sufficient difference in delays exists in input signals.

A compact arrayed-waveguide grating with small-bend waveguides incorporating air trenches and high mesa structures has been proposed. An 8-channel, 100-GHz-spacing silica arrayed-waveguide grating was fabricated, and its size was reduced dramatically to 1/4 of that of a conventional device.

This paper presents batch processing protocols for efficiently proving a great deal of partial knowledge. These protocols reduce the computation and communication costs for a MIX-net and secure circuit evaluation. The efficiency levels of the proposed protocols are estimated based on the implementation results of a secure circuit evaluation with batch processing.

In recent years, certain countermeasures against differential power analysis (DPA) at the logic level have been proposed. Recently, Popp and Mangard proposed a new countermeasure-masked dual-rail pre-charge logic (MDPL); this countermeasure combines dual-rail circuits with random masking to improve the wave dynamic differential logic (WDDL). They claimed that it could implement secure circuits using a standard CMOS cell library without special constraints for the place-and-route method because the difference between the loading capacitances of all the pairs of complementary logic gates in MDPL can be compensated for by the random masking. In this paper, we particularly focus on the signal transition of MDPL gates and evaluate the DPA-resistance of MDPL in detail. Our evaluation results reveal that when the input signals have different delay times, leakage occurs in the MDPL as well as WDDL gates, even if MDPL is effective in reducing the leakage caused by the difference in loading capacitances. Furthermore, in order to validate our evaluation, we demonstrate a problem with different input signal delays by conducting measurements for an FPGA.

Cognitive radio and/or SDR (Software Defined Radio) inherently requires multi-band and multi standard wireless circuit. The circuit is implemented based on Si CMOS technology. In this article, the recent progress of Si RF CMOS is described and the reconfigurable RF CMOS circuit which was proposed by the authors is introduced. At the present and in the future, several kind of Si CMOS technology can be used for RF CMOS circuit implementation. The realistic RF CMOS circuit implementation toward cognitive and/or SDR is discussed.

This paper presents some structures of artificial coplanar waveguide with very slow phase velocity and their applications to a design of compact 3-dB branch-line couplers. The slow-wave structure is constructed by periodically loading both of series inductance and shunt capacitance. First, a basic miniature branch-line coupler is designed and consequently considerable size-reduction of about 1/4 is obtained. Next, a broadband design technique is described using open-circuited quarter-wavelength series-stubs added at each port as a matching network. By size-reducing the series-stubs and branchline sections, a very compact broadband coupler with a good hybrid performance over a wide bandwidth of 31 percent or more is realized. The design concepts and procedures are verified both numerically and experimentally.

In this paper, we propose a novel migration method. In this method, the resultant placement retains the structure of the original placement, called model placement, as much as possible. For this purpose, we minimize the sum of the difference in area between the model placement and the relocated one and the total amount of displacement between them. Moreover, to achieve a short runtime, we limit the solution space and change the packing origin in the optimization process. We construct the system on Sequence-Pair. Experimental results show that our approach preserves the chip area and the overall circuit structure with 98% less runtime than that realized by naive simulated annealing.

A new algorithm is proposed to reduce the area of a pipelined circuit using a combination of multi-clock cycle paths, clock scheduling and delay balancing. The algorithm analyzes the circuit and replaces intermediate registers with delay elements under the condition that the circuit works correctly at given target clock-period range with the smaller area. Experiments with pipelined multipliers verify that the proposed algorithm can reduce the area of a pipelined circuit without degrading performance.

Closed-form expressions for a crosstalk noise amplitude and worst-case delay in capacitively coupled two-line and three-line systems are derived assuming bus lines and other signal lines in a VLSI. Two modes are studied; a case that adjacent lines are driven from the same direction, and the other case that adjacent lines are driven from the opposite direction. Beside, a junction capacitance of a driver MOSFET is considered. The closed-form expressions are useful for circuit designers in an early stage of a VLSI design to give insight to interconnection problems. The expressions are extensively compared and fitted to SPICE simulations. The relative and absolute errors in the crosstalk noise amplitude are within 63.8% and 0.098 E (where E is a supply voltage), respectively. The relative error in the worst-case delay is less than 8.1%.

A method of sequential circuit synthesis is proposed for Single-Flux-Quantum (SFQ) digital circuits. Since all logic gates of SFQ digital circuits are driven by a clock signal, methods of sequential circuit synthesis for semiconductor digital circuits cannot derive the full power of high-throughput computation of SFQ circuit technology. In the method, a 'state module' consisting of a DFF and several AND gates is used. First, states of a sequential machine are encoded by one-hot encoding and state modules are assigned to the states one-by-one, and then, the modules are connected with each other according to the state transition. For the connection, Confluence Buffers (CBs), i.e., merger gates without clock signals are used. Consequently, gates driven by a clock signal are removed from its feedback loops, and therefore, a high-throughput SFQ sequential circuit is achieved. The experimental results on benchmark circuits show that compared with a conventional method for semiconductor digital circuits, the proposed method synthesizes circuits that work with 4.9 times higher clock frequency and have 17.3% more gates on average.

A single-chip ubiquitous sensor network (USN) system-on-a-chip (SoC) for small program memory size and low power has been proposed and integrated in a 0.18-µm CMOS technology. Proposed single-chip USN SoC is mainly consists of radio for 868/915 MHz, analog building block, complete digital baseband physical layer (PHY) and media access control (MAC) functions. The transceiver's analog building block includes a low-noise amplifier, mixer, channel filter, receiver signal-strength indication, frequency synthesizer, voltage-controlled oscillator, and power amplifier. In addition, digital building block consists of differential binary phase-shift keying (DPSK) modulation, demodulation, carrier frequency offset compensation, auto-gain control, embedded 8-bit microcontroller, and digital MAC function. Digital MAC function supports 128 bit advanced encryption standard (AES), cyclic redundancy check (CRC), inter-symbol timing check, MAC frame control, and automatic retransmission. These digital MAC functions reduce the processing power requirements of embedded microcontroller and program memory size by up to 56%. The cascaded noise figure and sensitivity of the overall receiver are 9.5 dB and -99 dBm, respectively. The overall transmitter achieves less than 6.3% error vector magnitude (EVM). The current consumption is 14 mA for reception mode and 16 mA for transmission mode.

Design automation of LCD driver circuits is not sophisticatedly established. Display fineness of an LCD panel depends on a performance metric, ratio of pixel voltage to video voltage (RPV). However, there are several other important metrics, such as area, and the best circuit cannot be decided uniquely. This paper proposes a design automation technique for a LCD column driver to provide several circuit design results with different performance so that designers can select an appropriate design among them. The proposed technique is evaluated with an actual design data, and experimental results show that the proposed method successfully performs technology migration by transistor sizing. Also, the proposed technique is experimentally verified from points of solution quality and computational time.

Although much research effort has been devoted to the minimization of total power consumption caused by the clock tree, no attention has been paid to the minimization of the peak current caused by it. In this paper, we propose an opposite-phase clock scheme to reduce the peak current incurred by the clock tree. Our basic idea is to balance the charging and discharging activities. According to the output operation, the clock buffers that transit simultaneously are divided into two groups: half of the clock buffers transit at the same phase of the clock source, while the other half transit at the opposite phase of the clock source. As a consequence, the opposite-phase clock scheme significantly reduces the peak current caused by the clock tree. Experimental data show that our approach can be applied at different design stages in the existing design flow.

This paper proposes new scheduling methods for asynchronous circuits with bundled-data implementations. Since operations in asynchronous circuits start after the completion of a previous operation, this method approximates the set of start times for each operation using the delay of the resources. Next, this method decides on control steps from the approximated sets of start times, which are used in scheduling algorithms. This paper extends two scheduling algorithms used for synchronous circuits so that the approximated sets of start times and the decided control steps are used. Finally, this paper shows the effectiveness of our proposed methods by comparing scheduling results with ones obtained by the original two scheduling algorithms.